Shop Page
Filters Sort results
Reset Apply
Pic | Add | Part Number | Description | Details | View | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| All Small Parts (205) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | IC36 | IC36 Increase Bushing 2-083 to 3-065The IC36 is a driveshaft increase bushing… Show more (+) IC36 Increase Bushing 2-083 to 3-065The IC36 is a driveshaft increase bushing transitioning from a 2-083 tube (2.0″ OD x 0.083″ wall) to a 3-065 tube (3.0″ OD x 0.065″ wall). Inside diameter is 1.834″, outer diameter is 3.0″, and length is 1.0″.SpecificationsPart Number: IC36From Tube: 2-083To Tube: 3-065Inside Diameter: 1.834″Outer Diameter: 3.0″Length: 1.0″When fitting the IC36, confirm the existing tube is 2.0″ OD x 0.083″ wall (2-083) and the target tube is 3.0″ OD x 0.065″ wall (3-065). The 1.834″ ID accommodates the 2-083 tube end. Verify the tube is cut square and free of burrs before inserting into the bushing. Confirm the target 3-065 tube OD is exactly 3.0″ to ensure the bushing OD provides a flush weld joint.This bushing steps from a 2″ small-tube assembly to a 3″ large-tube assembly. The 0.083″ to 0.065″ wall change between the two tubes is relevant for weld preparation; the thinner 3-065 wall requires adjusted weld parameters. The 1.0″ length provides adequate weld land on both tube surfaces.The IC36 ID of 1.834″ and OD of 3.0″ are the defining fitment dimensions. Verify both tube specifications (2-083 inner and 3-065 outer) before ordering. A wall thickness mismatch on either tube will affect ID clearance and OD fit at the weld joint. Show less (-) | From Tube: 2-083 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | IC38 | IC38 Increase Bushing 25-083 to 3-083The IC38 is a driveshaft increase bushing… Show more (+) IC38 Increase Bushing 25-083 to 3-083The IC38 is a driveshaft increase bushing transitioning from a 25-083 tube (2.5″ OD x 0.083″ wall) to a 3-083 tube (3.0″ OD x 0.083″ wall). Inside diameter is 2.334″, outer diameter is 3.0″, and installed length is 0.8″. When installed, the bushing produces a 0.25″ lip overlap.SpecificationsPart Number: IC38From Tube: 25-083To Tube: 3-083Inside Diameter: 2.334″Outer Diameter: 3.0″Length: 0.8″Notes: 0.25″ lip when installedWhen fitting the IC38, confirm the existing driveshaft tube OD is 2.5″ with a 0.083″ wall (25-083) and the target tube is 3.0″ OD x 0.083″ wall (3-083). The 2.334″ ID accepts the 25-083 tube end with the 0.083″ wall factored in. Verify the tube end is cut square and deburred before insertion. The 0.25″ lip produced when installed must be accounted for in the overall assembly length.The IC38 steps from the common 2.5″ to 3.0″ OD, both at 0.083″ wall. A heavier wall (0.095″) will reduce the ID clearance and prevent the bushing from seating correctly. Confirm both tube wall thicknesses before ordering.The IC38 ID of 2.334″ and OD of 3.0″ are the critical matching dimensions. The 0.25″ installed lip and 0.8″ length must be factored into the assembly geometry. Verify both tube specs (25-083 inner and 3-083 outer) before ordering the IC38. Show less (-) | From Tube: 25-083 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 230123-15 | 230123-15 Washer and Snap Ring 1.03″ ID x 1.875″ ODThe 230123-15 is… Show more (+) 230123-15 Washer and Snap Ring 1.03″ ID x 1.875″ ODThe 230123-15 is a driveshaft washer and snap ring with an inside diameter of 1.03″, an outside diameter of 1.875″, and a thickness of 0.125″. Used in driveshaft assembly applications where these bore and OD dimensions are required.SpecificationsPart Number: 230123-15Inside Diameter: 1.03″Outside Diameter: 1.875″Thickness: 0.125″When selecting the 230123-15, verify the bore (1.03″) and OD (1.875″) match the application requirements. The 1.03″ ID positions this washer over a shaft of that nominal diameter. Confirm the shaft OD and the mating housing or recess dimension against the 1.875″ OD before ordering. The ID, OD, and thickness are all functional dimensions.The 0.125″ thickness of the 230123-15 is a thin shim washer. Verify all three dimensions against the assembly drawing. The 230123-6 (1.281″ ID, 2.75″ OD, 0.156″ thick) is the larger variant in the same series for applications requiring a larger bore and OD engagement.The 1.03″ ID and 1.875″ OD are the primary fitment dimensions for the 230123-15. Confirm both against the target assembly. Using a washer with the wrong ID or OD will affect axial positioning and may allow the component to shift in service. Show less (-) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 230123-6 | 230123-6 Washer and Snap Ring 1.281″ ID x 2.75″ ODThe 230123-6 is… Show more (+) 230123-6 Washer and Snap Ring 1.281″ ID x 2.75″ ODThe 230123-6 is a driveshaft washer and snap ring with an inside diameter of 1.281″, an outside diameter of 2.75″, and a thickness of 0.156″. Used in driveshaft assembly applications where these bore and OD dimensions are required.SpecificationsPart Number: 230123-6Inside Diameter: 1.281″Outside Diameter: 2.75″Thickness: 0.156″When selecting the 230123-6, verify the bore (1.281″) and OD (2.75″) both match the application. The 1.281″ ID positions this washer over a shaft or hub of that nominal diameter. The 2.75″ OD must clear or seat against the mating bore or recess in the assembly. The ID, OD, and thickness are all functional dimensions.The 230123-6 at 0.156″ thickness is used where a defined axial shim dimension is needed along with controlled bore and OD engagement. Selecting by part number alone without verifying all three dimensions against the assembly drawing will result in incorrect fitment.The 1.281″ ID and 2.75″ OD are the primary dimensions for the 230123-6. The 230123-15 (1.03″ ID, 1.875″ OD, 0.125″ thick) covers a different bore and OD range in the same series. Confirm all three dimensions (ID, OD, thickness) before ordering the 230123-6. Show less (-) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 2515-100 | 2515-100 Washer and Snap Ring Thickness 1.0″The 2515-100 is a driveshaft washer… Show more (+) 2515-100 Washer and Snap Ring Thickness 1.0″The 2515-100 is a driveshaft washer and snap ring with a thickness of 1.0″. Used in driveshaft assembly applications requiring a 1.0″ spacer or adjustment dimension.SpecificationsPart Number: 2515-100Thickness: 1.0″When selecting the 2515-100, confirm the required spacer or shim thickness is 1.0″. This is significantly thicker than the 2715-series shims and is used for coarser axial positioning or spacer applications in driveshaft assembly. It may serve as a spacer to establish correct yoke or component positioning, or as a thrust washer requiring a defined 1.0″ gap.The 1.0″ thickness of the 2515-100 places it in a different application range from the thin shims in the 2715 series. Confirm the application requires this specific thickness before ordering.Verify the 2515-100 thickness (1.0″) matches the assembly requirement. Confirm the component series and application to ensure this washer is the correct fitment for the target driveshaft assembly. Show less (-) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 2715-016 | 2715-016 Washer and Snap Ring Thickness 0.1″The 2715-016 is a driveshaft washer… Show more (+) 2715-016 Washer and Snap Ring Thickness 0.1″The 2715-016 is a driveshaft washer and snap ring with a thickness of 0.1″. Used in U-joint and driveshaft assembly applications where a 0.1″ shim dimension is required.SpecificationsPart Number: 2715-016Thickness: 0.1″When selecting the 2715-016, confirm the required shim thickness is 0.1″. This is thicker than the 2715-285 (0.04″) and provides a larger axial adjustment increment for U-joint cap seating or driveshaft assembly endplay control. Select the thickness that achieves the specified endplay per the assembly procedure.Washer and snap ring shims set endplay or preload in driveshaft component assemblies. The 0.1″ thickness of the 2715-016 provides a larger increment than the 0.04″ 2715-285 version. Incorrect shim thickness will affect joint engagement and bearing life.Confirm the 2715-016 thickness (0.1″) against the assembly requirement before ordering. Cross-reference with other shim thicknesses in the 2715 series to determine which combination achieves the specified endplay for the target application. Show less (-) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 2715-285 | 2715-285 Washer and Snap Ring Thickness 0.04″The 2715-285 is a driveshaft washer… Show more (+) 2715-285 Washer and Snap Ring Thickness 0.04″The 2715-285 is a driveshaft washer and snap ring with a thickness of 0.04″. Used in U-joint and driveshaft assembly applications where this shim dimension is required.SpecificationsPart Number: 2715-285Thickness: 0.04″When selecting the 2715-285, confirm the required shim thickness is 0.04″. This is a thin-shim washer used for precise axial positioning in U-joint cap seating or endplay control in driveshaft assembly. Multiple thicknesses are available in this series; the 2715-285 at 0.04″ and the 2715-016 at 0.1″ cover a range of adjustment requirements.Select the thickness that achieves the specified endplay per the assembly procedure. Using an incorrect thickness will affect U-joint cap engagement or bearing preload and may cause premature component wear.Verify the 2715-285 thickness (0.04″) matches the required shim spec before ordering. Cross-reference with other shim thicknesses in the 2715 series to determine which combination achieves the specified endplay for the target application. Show less (-) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 1-2020 | 1-2020 1350 / 1410 Universal Joint Strap KitThe 1-2020 is a 1350… Show more (+) 1-2020 1350 / 1410 Universal Joint Strap KitThe 1-2020 is a 1350 / 1410 series universal joint strap kit. It secures U-joint caps measuring 1.188″ in diameter, with a bolt center-to-center spacing of 1.656″ and bolt length of 1.5″. Thread specification is .312-24; fasteners torque to 32 ft-lb.SpecificationsPart Number: 1-2020Series: 1350 / 1410Fits Cap Dia: 1.188″Center to Center: 1.656″Bolt Length: 1.5″Thread Dia: .312-24Bolt Torque: 32 ft-lbWhen installing the 1-2020, confirm U-joint cap diameter is 1.188″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 32 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The 1350 / 1410 series defines the cap dimensions this strap is engineered for. The 1.656″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 1-2020 against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 1.5 Bolt Torque: 32 ft-lb Center to Center: 1.656 Fits Cap Dia: 1.188 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 1-2021 | 1-2021 1480 / 1550 Universal Joint Strap KitThe 1-2021 is a 1480… Show more (+) 1-2021 1480 / 1550 Universal Joint Strap KitThe 1-2021 is a 1480 / 1550 series universal joint strap kit. It secures U-joint caps measuring 1.375″ in diameter, with a bolt center-to-center spacing of 2.13″ and bolt length of 0.75″. Thread specification is .375-24; fasteners torque to 52 ft-lb.SpecificationsPart Number: 1-2021Series: 1480 / 1550Fits Cap Dia: 1.375″Center to Center: 2.13″Bolt Length: 0.75″Thread Dia: .375-24Bolt Torque: 52 ft-lbWhen installing the 1-2021, confirm U-joint cap diameter is 1.375″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 52 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The 1480 / 1550 series defines the cap dimensions this strap is engineered for. The 2.13″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 1-2021 against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 0.75 Bolt Torque: 52 ft-lb Center to Center: 2.13 Fits Cap Dia: 1.375 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 1-2022 | 1-2022 1310 / 1330 Universal Joint Strap KitThe 1-2022 is a 1310… Show more (+) 1-2022 1310 / 1330 Universal Joint Strap KitThe 1-2022 is a 1310 / 1330 series universal joint strap kit. It secures U-joint caps measuring 1.062″ in diameter, with a bolt center-to-center spacing of 1.594″ and bolt length of 0.594″. Thread specification is .250-28; fasteners torque to 15 ft-lb.SpecificationsPart Number: 1-2022Series: 1310 / 1330Fits Cap Dia: 1.062″Center to Center: 1.594″Bolt Length: 0.594″Thread Dia: .250-28Bolt Torque: 15 ft-lbWhen installing the 1-2022, confirm U-joint cap diameter is 1.062″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 15 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The 1310 / 1330 series defines the cap dimensions this strap is engineered for. The 1.594″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 1-2022 against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 594 Bolt Torque: 15 ft-lb Center to Center: 1.594 Fits Cap Dia: 1.062 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 1-2023 | 1-2023 7260 Universal Joint Strap KitThe 1-2023 is a 7260 series universal… Show more (+) 1-2023 7260 Universal Joint Strap KitThe 1-2023 is a 7260 series universal joint strap kit. It secures U-joint caps measuring 1.078″ in diameter, with a bolt center-to-center spacing of 1.5″ and bolt length of 0.625″. Thread specification is .250-28; fasteners torque to 15 ft-lb.SpecificationsPart Number: 1-2023Series: 7260Fits Cap Dia: 1.078″Center to Center: 1.5″Bolt Length: 0.625″Thread Dia: .250-28Bolt Torque: 15 ft-lbWhen installing the 1-2023, confirm U-joint cap diameter is 1.078″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 15 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The 7260 series defines the cap dimensions this strap is engineered for. The 1.5″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 1-2023 against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 625 Bolt Torque: 15 ft-lb Center to Center: 1.5 Fits Cap Dia: 1.078 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 1-2025 | 1-2025 3R Universal Joint Strap KitThe 1-2025 is a 3R series universal… Show more (+) 1-2025 3R Universal Joint Strap KitThe 1-2025 is a 3R series universal joint strap kit. It secures U-joint caps measuring 1.125″ in diameter, with a bolt center-to-center spacing of 1.812″ and bolt length of 1.5″. Thread specification is .312-24; fasteners torque to 32 ft-lb.SpecificationsPart Number: 1-2025Series: 3RFits Cap Dia: 1.125″Center to Center: 1.812″Bolt Length: 1.5″Thread Dia: .312-24Bolt Torque: 32 ft-lbWhen installing the 1-2025, confirm U-joint cap diameter is 1.125″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 32 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The 3R series defines the cap dimensions this strap is engineered for. The 1.812″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 1-2025 against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 1.5 Bolt Torque: 32 ft-lb Center to Center: 1.812 Fits Cap Dia: 1.125 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 1-1930 | 1-1930 1485 / 1550 Universal Joint Strap KitThe 1-1930 is a 1485… Show more (+) 1-1930 1485 / 1550 Universal Joint Strap KitThe 1-1930 is a 1485 / 1550 series universal joint strap kit. It secures U-joint caps measuring 1.375″ in diameter, with a bolt center-to-center spacing of 1.938″ and bolt length of 1.281″. Thread specification is .312-24; fasteners torque to 32 ft-lb.SpecificationsPart Number: 1-1930Series: 1485 / 1550Fits Cap Dia: 1.375″Center to Center: 1.938″Bolt Length: 1.281″Thread Dia: .312-24Bolt Torque: 32 ft-lbWhen installing the 1-1930, confirm U-joint cap diameter is 1.375″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 32 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The 1485 / 1550 series defines the cap dimensions this strap is engineered for. The 1.938″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 1-1930 against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 1.281 Bolt Torque: 32 ft-lb Center to Center: 1.938 Fits Cap Dia: 1.375 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 1-1945 | 1-1945 1610 Universal Joint Strap KitThe 1-1945 is a 1610 series universal… Show more (+) 1-1945 1610 Universal Joint Strap KitThe 1-1945 is a 1610 series universal joint strap kit. It secures U-joint caps measuring 1.875″ in diameter, with a bolt center-to-center spacing of 2.5″ and bolt length of 0.75″. Thread specification is .375-24; fasteners torque to 52 ft-lb.SpecificationsPart Number: 1-1945Series: 1610Fits Cap Dia: 1.875″Center to Center: 2.5″Bolt Length: 0.75″Thread Dia: .375-24Bolt Torque: 52 ft-lbWhen installing the 1-1945, confirm U-joint cap diameter is 1.875″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 52 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The 1610 series defines the cap dimensions this strap is engineered for. The 2.5″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 1-1945 against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 0.75 Bolt Torque: 52 ft-lb Center to Center: 2.5 Fits Cap Dia: 1.875 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 1-1946 | 1-1946 1710 / 1760 / 1810 Universal Joint Strap KitThe 1-1946 is… Show more (+) 1-1946 1710 / 1760 / 1810 Universal Joint Strap KitThe 1-1946 is a 1710 / 1760 / 1810 series universal joint strap kit. It secures U-joint caps measuring 1.938″ in diameter, with a bolt center-to-center spacing of 2.812″ and bolt length of 1.0″. Thread specification is .500-20; fasteners torque to 125 ft-lb.SpecificationsPart Number: 1-1946Series: 1710 / 1760 / 1810Fits Cap Dia: 1.938″Center to Center: 2.812″Bolt Length: 1.0″Thread Dia: .500-20Bolt Torque: 125 ft-lbWhen installing the 1-1946, confirm U-joint cap diameter is 1.938″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 125 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The 1710 / 1760 / 1810 series defines the cap dimensions this strap is engineered for. The 2.812″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 1-1946 against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 1 Bolt Torque: 125 ft-lb Center to Center: 2.812 Fits Cap Dia: 1.938 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 140-70-18X | 140-70-18X SPL140 Universal Joint Strap KitThe 140-70-18X is a SPL140 series universal… Show more (+) 140-70-18X SPL140 Universal Joint Strap KitThe 140-70-18X is a SPL140 series universal joint strap kit. It secures U-joint caps measuring 2.362″ in diameter, with a bolt center-to-center spacing of 3.0″ and bolt length of 0.984″. Thread specification is M12 X 1.25 6G; fasteners torque to 115 ft-lb.SpecificationsPart Number: 140-70-18XSeries: SPL140Fits Cap Dia: 2.362″Center to Center: 3.0″Bolt Length: 0.984″Thread Dia: M12 X 1.25 6GBolt Torque: 115 ft-lbWhen installing the 140-70-18X, confirm U-joint cap diameter is 2.362″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 115 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The SPL140 series defines the cap dimensions this strap is engineered for. The 3.0″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 140-70-18X against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 984 Bolt Torque: 115 ft-lb Center to Center: 3 Fits Cap Dia: 2.362 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 170-70-18X | 170-70-18X SPL170 Universal Joint Strap KitThe 170-70-18X is a SPL170 series universal… Show more (+) 170-70-18X SPL170 Universal Joint Strap KitThe 170-70-18X is a SPL170 series universal joint strap kit. It secures U-joint caps measuring 2.165″ in diameter, with a bolt center-to-center spacing of 3.228″ and bolt length of 0.984″. Thread specification is M12 X 1.25 6G; fasteners torque to 115 ft-lb.SpecificationsPart Number: 170-70-18XSeries: SPL170Fits Cap Dia: 2.165″Center to Center: 3.228″Bolt Length: 0.984″Thread Dia: M12 X 1.25 6GBolt Torque: 115 ft-lbWhen installing the 170-70-18X, confirm U-joint cap diameter is 2.165″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 115 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The SPL170 series defines the cap dimensions this strap is engineered for. The 3.228″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 170-70-18X against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 984 Bolt Torque: 115 ft-lb Center to Center: 3.228 Fits Cap Dia: 2.165 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 2-70-18X | 2-70-18X 1210 / 1310 / 1330 Universal Joint Strap KitThe 2-70-18X is… Show more (+) 2-70-18X 1210 / 1310 / 1330 Universal Joint Strap KitThe 2-70-18X is a 1210 / 1310 / 1330 series universal joint strap kit. It secures U-joint caps measuring 1.062″ in diameter, with a bolt center-to-center spacing of 1.587″ and bolt length of 0.625″. Thread specification is .250-28; fasteners torque to 15 ft-lb.SpecificationsPart Number: 2-70-18XSeries: 1210 / 1310 / 1330Fits Cap Dia: 1.062″Center to Center: 1.587″Bolt Length: 0.625″Thread Dia: .250-28Bolt Torque: 15 ft-lbWhen installing the 2-70-18X, confirm U-joint cap diameter is 1.062″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 15 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The 1210 / 1310 / 1330 series defines the cap dimensions this strap is engineered for. The 1.587″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 2-70-18X against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 625 Bolt Torque: 15 ft-lb Center to Center: 1.587 Fits Cap Dia: 1.062 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 2-70-28X | 2-70-28X 1330 Universal Joint Strap KitThe 2-70-28X is a 1330 series universal… Show more (+) 2-70-28X 1330 Universal Joint Strap KitThe 2-70-28X is a 1330 series universal joint strap kit. It secures U-joint caps measuring 1.062″ in diameter, with a bolt center-to-center spacing of 1.587″ and bolt length of 1.438″. Thread specification is .312-24; fasteners torque to 15 ft-lb.SpecificationsPart Number: 2-70-28XSeries: 1330Fits Cap Dia: 1.062″Center to Center: 1.587″Bolt Length: 1.438″Thread Dia: .312-24Bolt Torque: 15 ft-lbWhen installing the 2-70-28X, confirm U-joint cap diameter is 1.062″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 15 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The 1330 series defines the cap dimensions this strap is engineered for. The 1.587″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 2-70-28X against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 1.438 Bolt Torque: 15 ft-lb Center to Center: 1.587 Fits Cap Dia: 1.062 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 2-70-48X | 2-70-48X 3R Universal Joint Strap KitThe 2-70-48X is a 3R series universal… Show more (+) 2-70-48X 3R Universal Joint Strap KitThe 2-70-48X is a 3R series universal joint strap kit. It secures U-joint caps measuring 1.125″ in diameter, with a bolt center-to-center spacing of 1.8″ and bolt length of 1.5″. Thread specification is .312-24; fasteners torque to 32 ft-lb.SpecificationsPart Number: 2-70-48XSeries: 3RFits Cap Dia: 1.125″Center to Center: 1.8″Bolt Length: 1.5″Thread Dia: .312-24Bolt Torque: 32 ft-lbWhen installing the 2-70-48X, confirm U-joint cap diameter is 1.125″ before ordering. Mixing strap kits across series produces incorrect center-to-center geometry and unreliable cap retention. Torque fasteners to 32 ft-lb in a cross pattern to seat caps evenly against both yoke ears.The 3R series defines the cap dimensions this strap is engineered for. The 1.8″ center-to-center dimension must correspond to the slot geometry in your yoke ears. Cross-reference the 2-70-48X against your yoke specification to confirm compatibility before installation. Show less (-) | Bolt Length: 1.5 Bolt Torque: 32 ft-lb Center to Center: 1.8 Fits Cap Dia: 1.125 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
