Shop Page
Filters Sort results
Reset Apply
Pic | Add | Part Number | Description | Details | View | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Univeral Joints (178) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-788X | 5-788X is a Spicer sealed combination U-joint for the 1310X7260 series, bridging… Show more (+) 5-788X is a Spicer sealed combination U-joint for the 1310X7260 series, bridging a 1310 driveshaft end (1.063" cap, 3.219" width) to a 7260 (Detroit) mechanical end (1.078" cap, 2.125" width). The cap diameters are close but not identical: 1.063" versus 1.078". Do not substitute a standard 1310 joint (1.062"/1.063" on both sides) — the 7260 bore requires the correct 1.078" cap for proper fit.Cap Dia 1 (7260 side): 1.078"Width 1 (7260): 2.125"Cap Dia 2 (1310 side): 1.063"Width 2 (1310): 3.219"Lube: No (sealed)Style: Combo (OSR/ISR)UDS equivalent: 5-788XU. Spicer brand used when OEM specification or documentation requires the Spicer part number.Browse all universal joints for all available series.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: SPICER Cap Dia 1: 1.078 Cap Dia 2: 1.063 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-793X | 5-793X Spicer — 1330X3R Sealed Combination U-JointThe 5-793X is a Spicer sealed… Show more (+) 5-793X Spicer — 1330X3R Sealed Combination U-JointThe 5-793X is a Spicer sealed combination universal joint for connecting the 1330 series to the 3R Saginaw end in an OSR (Outside Snap Ring) or ISR (Inside Snap Ring) retention application. Sealed construction means there are no grease fittings — the bearing needle packs are lubed at the factory and the cups are sealed for the service life of the joint.SpecValueCap Dia 1 (3R)1.125"Width 12.556"Cap Dia 2 (1330)1.063"Width 23.625"LubeNo (sealed)StyleCombo — OSR/ISRThe 1330 series uses the same 1.063" cap diameter as 1310 but with a wider width (3.625" vs. 3.219"). A 1310 U-joint will not correctly fill the 1330 yoke due to the width difference even though the cap diameter matches.See all universal joints for full combo and standard selections.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: SPICER Cap Dia 1: 1.125 Cap Dia 2: 1.063 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 3-1448XU | 3-1448XU is a UDS combination U-joint for connecting 1410 series and 1480… Show more (+) 3-1448XU is a UDS combination U-joint for connecting 1410 series and 1480 series driveshaft ends. Both series use large-diameter caps (1.188" for 1410; 1.375" for 1480), and both operate in heavy-duty truck applications — but the cap sizes are not interchangeable. This combo cross eliminates the need for a new yoke when one end of the driveshaft interfaces with 1410 hardware and the other requires 1480.The 1480 series (1.375" cap) is a step up in capacity from 1410 (1.188" cap). When only one end of the driveshaft has been upgraded to 1480 and the other remains 1410, the 3-1448XU bridges the gap.Cap Dia 1 (1410 side): 1.188"Width 1: 4.188"Cap Dia 2 (1480 side): 1.375"Width 2: 4.188"Lube: No (sealed)Series: 1410X1480Sealed (non-greaseable) construction means no periodic regreasing, but also no opportunity to flush contaminated grease. Inspect for wear at the normal driveshaft service intervals.Browse all universal joints for more heavy-duty conversion options.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 1.188 Cap Dia 2: 1.375 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-2140XU | 5-2140XU — 2RX1310 Saginaw Combination U-JointThe 5-2140XU is a Spicer combination universal… Show more (+) 5-2140XU — 2RX1310 Saginaw Combination U-JointThe 5-2140XU is a Spicer combination universal joint connecting the 2R Saginaw series to the 1310 driveshaft series. The 2R is a smaller Saginaw interface than the 3R, using a 1.000" cap diameter. The 1310 driveshaft side uses the standard 1.063" cap. This combination cross allows a direct 2R-to-1310 connection without any yoke modification.ParameterValueCap Dia 1 (2R side)1.000"Width 1 (2R)2.344"Cap Dia 2 (1310)1.063"Width 2 (1310)3.219"LubeYesSeries2RX1310The smaller 1.000" cap on the 2R side transmits less torque than the 1.063" 1310 cap — the assembly torque limit is set by the smaller-capacity side. Verify that the torque load on your application falls within the 2R series rating.See all universal joints for full selection.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: SPICER Cap Dia 1: 1.000 Cap Dia 2: 1.063 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-3022-1X | 5-3022-1X is the Spicer OEM part number for the 3RX1310 Saginaw combination… Show more (+) 5-3022-1X is the Spicer OEM part number for the 3RX1310 Saginaw combination universal joint. It is the direct industry-standard reference for this conversion, bridging 1310 series driveshaft ends to 3R Saginaw steering column interfaces.The Saginaw 3R joint is found in many GM column assemblies and transfer case applications. When building or rebuilding a driveshaft that must interface with this end, the 5-3022-1X provides the specified conversion in a single cross component. UDS equivalent: 5-3022-1XU.Cap Dia 1 (3R side): 1.125"Width 1: 2.556"Cap Dia 2 (1310 side): 1.063"Width 2: 3.219"Lube: Yes (greaseable)Series: 3RX1310Before ordering, verify which end of your application is the 3R (Saginaw) end and which is the 1310 driveshaft end. The earwidths must match the figures above on each corresponding side.Browse all universal joints for additional combo and standard U-joint options.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: SPICER Cap Dia 1: 1.125 Cap Dia 2: 1.063 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-3022-1XU | 5-3022x UDS — 3RX1310 Saginaw Conversion Universal JointThe 5-3022x (part number 5-3022-1XU)… Show more (+) 5-3022x UDS — 3RX1310 Saginaw Conversion Universal JointThe 5-3022x (part number 5-3022-1XU) is a UDS combination U-joint for converting a 1310 series driveshaft end to a 3R/S44 Saginaw steering column end. The 3R series is the Saginaw steering column U-joint specification used in many General Motors vehicles. This combo joint allows 1310 driveshaft components to interface with the Saginaw column without modifying either end.SpecValueCap Dia 1 (1310)1.063"Width 1 (1310 side)3.219"Cap Dia 2 (3R)1.125"Width 2 (3R side)2.556"LubeYesSeries3RX1310Spicer equivalent: 5-3022-1X. The 1310 cap (1.062"/1.063") is the most common domestic automotive U-joint cap size. The 3R Saginaw cap at 1.125" is smaller than the 1310 in a different geometry — the combo cross handles both.See all universal joints for more Saginaw and standard conversion options.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 1.125 Cap Dia 2: 1.063 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-345X | 5-345X is the Spicer OEM combination U-joint for the 1410X4C conversion, identical… Show more (+) 5-345X is the Spicer OEM combination U-joint for the 1410X4C conversion, identical in function to the UDS equivalent 5-345XU. Spicer part numbers are the industry reference standard for U-joint cross-reference, making 5-345X the specification most commonly listed in OEM and fleet service manuals for this application.The 1410 series is heavily used in 3/4-ton and 1-ton domestic trucks, particularly Ford F-250 through F-350 and Dodge Ram 2500-3500 applications. The 1.188" cap diameter (1350/1410 cap family) provides higher torque capacity than the 1310 cap (1.062").Cap Dia 1 (1410): 1.188"Width 1: 4.188"Cap Dia 2 (4C Mech): 1.438"Width 2: 4.250"Lube: Yes (greaseable)Series: 1410X4CFor the same conversion without the Spicer brand, see 5-345XU.Browse all universal joints for complete listing.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: SPICER Cap Dia 1: 1.188 Cap Dia 2: 1.438 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-345XU | 5-345XU UDS — 1410X4C Combination Universal JointThe 5-345XU is a UDS-branded combination… Show more (+) 5-345XU UDS — 1410X4C Combination Universal JointThe 5-345XU is a UDS-branded combination U-joint that converts a 1410 series driveshaft connection to a 4C Mechanic (MECH) end. The 1410 series is a widely used heavy-duty domestic truck U-joint series with 1.188" cap diameter — the same cap size as the 1350 series but in a different width configuration. The 4C Mechanic end uses 1.438" caps.ParameterValueCap Dia 1 (1410)1.188"Width 14.188"Cap Dia 2 (4C Mech)1.438"Width 24.250"GreaseableYesSeries1410X4CSpicer equivalent: 5-345X. When the OEM-branded part is not required, the UDS version (5-345XU) serves the same application at the same dimensions. Verify earwidth of both yokes before installation to confirm this joint seats properly on both sides.Browse all universal joints for more conversion and standard options.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 1.188 Cap Dia 2: 1.438 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 6C-3XU | The 6C-3XU is a UDS heavy-duty combination universal joint designed to connect… Show more (+) The 6C-3XU is a UDS heavy-duty combination universal joint designed to connect the 1550 series driveshaft to a 6C Mechanic (MECH) end. The cross uses 1.375" caps on the 1550 side and 1.688" caps on the 6C Mechanic side — the different diameters allow each pair to properly seat in their respective yoke ear bores without modification.The 1550 series uses a 1.375" cap diameter, which is the same as the 1480 series cap but in a wider width. Confirm the earwidth of your 1550 yoke matches the 4.969" width listed for this joint before ordering.Cap Diameter 1: 1.375" (1550 side)Width 1: 4.969"Cap Diameter 2: 1.688" (6C Mechanic side)Width 2: 5.531"Lube: Yes (greaseable)Part number: 6C-3XUNote: OSR/WB MECH designation refers to the interface type at the mechanic end. Verify your application matches before ordering.Browse all universal joints for complete series and combination options.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 1.375 Cap Dia 2: 1.688 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-330X | 5-330X Spicer — 1650X7C Combination Universal JointThe 5-330X is a Spicer-branded combination… Show more (+) 5-330X Spicer — 1650X7C Combination Universal JointThe 5-330X is a Spicer-branded combination (combo) universal joint that bridges the 1650 series and 7C mechanical series. Combination U-joints use two different cap sizes on the same cross: one pair of caps fits the 1650 yoke ears, the other pair fits 7C mechanical yoke ears. This allows a direct connection between these two incompatible series without an adapter flange or additional hardware.DimensionValueCap Diameter 11.625"Cap Diameter 21.938"Width 15.594"Width 25.531"LubeYes (greaseable)Series1650X7CStyleCombo (OSR/WB MECH)The 1.938" cap diameter corresponds to the 1710/SPL100 series cap size. Before ordering, verify that both the 1650 and 7C yoke earwidths match the listed widths above — incorrect width causes the caps to contact the yoke ears improperly, leading to early bearing failure.Cross-reference: Spicer part number 5-330X. Compatible with grease fittings for periodic lubrication.See all universal joints for additional series and style options.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: SPICER Cap Dia 1: 1.625 Cap Dia 2: 1.938 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | UJ3287 | UJ3287 UDS 32x87mm Heavy Duty Sealed Universal Joint – OSR StyleThe UJ3287… Show more (+) UJ3287 UDS 32x87mm Heavy Duty Sealed Universal Joint – OSR StyleThe UJ3287 is a UDS heavy-duty sealed universal joint in the 32x87mm series. Cap diameter is 1.259″ and width is 3.425″. OSR (outside snap ring) retention style is used. This joint is sealed — no grease fitting — suitable for applications requiring a maintenance-free lube-for-life configuration.SpecificationsPart Number: UJ3287Brand: UDSSeries: 32×87Cap Diameter: 1.259″Width: 3.425″Style: OSRLube: No – sealedWhen installing the UJ3287, verify the yoke ear bores accept the 1.259″ cap diameter and the span between ears measures 3.425″. The OSR retention requires intact external snap ring grooves in both yoke ears. Because the UJ3287 is sealed, no re-greasing is possible after installation — service life is determined by seal and bearing wear rather than lube intervals.The 32×87 series designation refers to the metric cap dimensions (approximately 32mm diameter, 87mm width) used in European commercial vehicle and specialty driveline applications. Confirm these dimensions against the relevant OEM or chassis specification before ordering the UJ3287.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 1.259 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-3012X | 5-3012X UDS 3CRL Series Universal Joint – COMBO Style, CP3012 Heavy DutyThe… Show more (+) 5-3012X UDS 3CRL Series Universal Joint – COMBO Style, CP3012 Heavy DutyThe 5-3012X is a UDS 3CRL series heavy-duty universal joint in COMBO retention style. Cap diameter 1 is 1.124″ at 2.370″ width; cap diameter 2 is 1.437″ at 3.560″ width. A lube fitting is installed. This part cross-references as CP3012. Alternative references include 2-3012 and 114-3102.SpecificationsPart Number: 5-3012XBrand: UDSSeries: 3CRLCap Diameter 1: 1.124″ / Width 1: 2.370″Cap Diameter 2: 1.437″ / Width 2: 3.560″Style: COMBOLube: YesCross References: CP3012, 2-3012, 114-3102, 531When installing the 5-3012X, the 1.124″ cap axis must align with the yoke requiring that bore, while the 1.437″ cap axis aligns with the opposing yoke. The COMBO retention style accommodates differing retention methods on each axis. Confirm snap ring groove condition in both yoke sets before pressing caps.The 3CRL series designation is used in medium-duty commercial vehicle drivelines. Cross-reference the 5-3012X as CP3012 or 2-3012 if sourcing through alternate catalogs. The heavy-duty CP3012 designation indicates higher torque capacity within the 3CRL series — verify that both mating yokes are rated accordingly.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 1.124 Cap Dia 2: 1.437 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-1503X | 5-1503X UDS 1751 Series Universal Joint – 25×63.8mm OSR – Suzuki, Dodge… Show more (+) 5-1503X UDS 1751 Series Universal Joint – 25×63.8mm OSR – Suzuki, Dodge ColtThe 5-1503X is a UDS 1751 series universal joint with a 0.985″ (25mm) cap diameter and 2.517″ (63.8mm) width, OSR retention style, and a lube fitting installed. Specified applications include Suzuki, Mitsubishi Colt, Vista, Talent, Eclipse, and Ram 50.SpecificationsPart Number: 5-1503XBrand: UDSSeries: 1751Cap Diameter: 0.985″ (25mm)Width: 2.517″ (63.8mm)Style: OSRLube: YesApplication: Suzuki, Dodge Colt, Mitsubishi Vista, Talent, Eclipse, Ram 50When installing the 5-1503X, confirm the yoke ear bores accept the 0.985″ (25mm) cap diameter and the span measures 2.517″ (63.8mm). The OSR retention style requires undamaged snap ring grooves. The 1751 series dimensions are shared across multiple Mitsubishi and Suzuki platforms — verify the specific model application before ordering.The 5-1503X fits Mitsubishi Colt, Vista, Eclipse, and Ram 50 drivelines in addition to Suzuki applications. Confirm the 25×63.8mm metric dimensions against the OEM service data for your specific model year and drivetrain configuration before ordering.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 0.985 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 1751-22 | 1751-22 UDS 1751 Series Universal Joint – OSR Style, Suzuki ApplicationsThe 1751-22… Show more (+) 1751-22 UDS 1751 Series Universal Joint – OSR Style, Suzuki ApplicationsThe 1751-22 is a UDS 1751 series universal joint in OSR (outside snap ring) retention style. Cap diameter is 0.985″ and width is 2.517″. A lube fitting is installed. This part is noted for Suzuki and related driveline applications.SpecificationsPart Number: 1751-22Brand: UDSSeries: 1751Cap Diameter: 0.985″Width: 2.517″Style: OSRLube: YesApplication: Suzuki and moreWhen installing the 1751-22, confirm the yoke ear bores accept the 0.985″ cap diameter and the span between ears measures 2.517″. The OSR retention style requires undamaged external snap ring grooves in both yoke ears. The 1751 series is a small-diameter designation used in light-duty and import vehicle drivelines.The 1751-22 is applicable to Suzuki drivelines and potentially other import platforms sharing the 1751 series dimensions. Verify the exact cap and width dimensions against your specific Suzuki model service data before ordering.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 0.985 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 9951-23 | 9951-23 UDS Universal Joint – 30mm x 54.8mm ISR – Mitsubishi MonteroThe… Show more (+) 9951-23 UDS Universal Joint – 30mm x 54.8mm ISR – Mitsubishi MonteroThe 9951-23 is a UDS universal joint with a 1.181″ (30mm) cap diameter and 2.290″ (54.8mm) width, ISR (inside snap ring) retention style, with a lube fitting installed. This part is specified for the Mitsubishi Montero driveline.SpecificationsPart Number: 9951-23Brand: UDSCap Diameter: 1.181″ (30mm)Width: 2.290″ (54.8mm)Style: ISRLube: YesApplication: Mitsubishi MonteroWhen installing the 9951-23, confirm the Montero driveshaft yoke ear bores accept the 1.181″ (30mm) cap diameter and the span between ears measures 2.290″ (54.8mm). The ISR retention style uses internal snap rings — inspect the snap ring groove inside each yoke ear before pressing in new caps.Verify the 30×54.8mm metric dimensions against the Mitsubishi Montero service manual specification for the specific model year and drivetrain configuration before ordering the 9951-23.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 1.181 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 3-0485 | 3-0485 UDS 1485 Series Sealed Universal Joint – ISR Style, 2003+ Dodge… Show more (+) 3-0485 UDS 1485 Series Sealed Universal Joint – ISR Style, 2003+ Dodge 9.25″ Front AxleThe 3-0485 is a UDS 1485 series sealed universal joint in ISR (inside snap ring) retention style. Cap diameter is 1.375″ and width is 2.922″. This joint is sealed (no grease fitting) and is specified for 2003 and later Dodge vehicles equipped with a 9.25″ front axle.SpecificationsPart Number: 3-0485Brand: UDSSeries: 1485Cap Diameter: 1.375″Width: 2.922″Style: ISRLube: No – sealedApplication: 2003+ Dodge 9.25″ Front AxlesWhen installing the 3-0485, verify the Dodge front axle shaft yoke ear bores accept the 1.375″ cap diameter and the span between ears measures 2.922″. The ISR retention uses internal snap rings — inspect the groove condition in the yoke ears before pressing in caps. This sealed joint is designed for the Dodge 9.25″ independent front axle, confirmed for 2003 and later model years.The 1485 series sits above the 1480 and below the 1550 in torque capacity, and is used in high-load front axle applications. The 3-0485 is sealed at the factory; no grease is required or possible after installation. Verify model year and axle designation (9.25″ front) before ordering to distinguish from rear axle joint applications.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 1.375 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-760X | 5-760X UDS 1310WJ Series Sealed Universal Joint – ISR Style, Dana 30/35/44… Show more (+) 5-760X UDS 1310WJ Series Sealed Universal Joint – ISR Style, Dana 30/35/44 Front AxleThe 5-760X is a UDS 1310WJ series sealed (non-greasable) universal joint in ISR (inside snap ring) retention style. Cap diameter is 1.188″ and width is 2.188″. This joint is specified for front axle shaft applications on Dana 30, Dana 35, and Dana 44 axles used in Ford, Mopar, and GM vehicles.SpecificationsPart Number: 5-760XBrand: UDSSeries: 1310WJCap Diameter: 1.188″Width: 2.188″Style: ISRLube: No – sealedApplication: Dana 30, Dana 35, Dana 44 front axle shaft (Ford, Mopar, GM)When installing the 5-760X, confirm the front axle shaft yoke accepts the 1.188″ cap diameter and 2.188″ width. The ISR retention style uses internal snap rings — the 1310WJ designation indicates a wider journal spacing than a standard 1310, so verify the exact cap and width against your Dana axle shaft specification. The sealed construction eliminates the need for grease service on this joint.The 5-760X is cross-referenced as 5-297X in some catalogs. Verify Dana 30, 35, or 44 front axle shaft joint specification before ordering to confirm the 1.188″x2.188″ cap dimensions match your axle model year build.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 1.188 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 74081555U | 74081555 UDS 1555 Series Universal Joint – ISR Style, AAM 1555The 74081555… Show more (+) 74081555 UDS 1555 Series Universal Joint – ISR Style, AAM 1555The 74081555 is a UDS 1555 series universal joint in ISR (inside snap ring) retention style. Cap diameter is 1.375″ and width is 3.702″. A lube fitting is installed. This part corresponds to the AAM 1555 series designation used in American Axle & Manufacturing driveline applications.SpecificationsPart Number: 74081555Brand: UDSSeries: 1555Cap Diameter: 1.375″Width: 3.702″Style: ISRLube: YesApplication: AAM 1555 seriesWhen installing the 74081555, confirm the yoke ear bores accept the 1.375″ cap diameter and the span between ears measures 3.702″. The ISR retention style uses internal snap rings — inspect the groove condition inside each yoke ear before pressing in the caps. The AAM 1555 series is used in GM and Dodge heavy-duty rear driveline applications.The 1555 series is a high-torque designation above the 1480 and 1410 series. Cross-reference 74081555 against AAM 1555 catalog data to confirm the correct cap and width dimensions for your specific GM or Dodge platform before ordering.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 1.375 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-1330X | 5-1330X UDS 1330 Series Sealed Universal Joint – OSR StyleThe 5-1330X is… Show more (+) 5-1330X UDS 1330 Series Sealed Universal Joint – OSR StyleThe 5-1330X is a UDS 1330 series sealed (lube-for-life) universal joint. Cap diameter is 1.063″ and width is 3.625″. OSR (outside snap ring) retention style is used. This unit is sealed — no grease fitting — and ships with two snap ring sizes to accommodate yoke ear groove variation. Includes 2 snap ring sizes.SpecificationsPart Number: 5-1330XBrand: UDSSeries: 1330Cap Diameter: 1.063″Width: 3.625″Style: OSRLube: No – sealed, lube for lifeIncludes: 2 snap ring sizesWhen installing the 5-1330X, verify yoke ear bores are dimensioned for 1.063″ cap diameter and 3.625″ span. Because this joint is sealed at the factory, no re-greasing is possible — the service interval is determined by total wear rather than lube maintenance. The included two snap ring sizes allow fitment into yokes with slightly different groove depths.The 1330 series sits between the 1310 and 1350 in the torque capacity range. Confirm that both mating yokes are 1330 series before installation. The OSR retention style requires undamaged snap ring grooves — do not use yokes with wallowed or cracked groove walls with the 5-1330X.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 1.063 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | 5-92XU | 5-92X UDS L6N Series Universal Joint – ISR Style, Rockwell 861The 5-92X… Show more (+) 5-92X UDS L6N Series Universal Joint – ISR Style, Rockwell 861The 5-92X is a UDS universal joint in the Rockwell L6N series. Cap diameter is 0.971″ and width is 1.445″. ISR (inside snap ring) retention style is used with a lube fitting installed. This part is referenced for Rockwell L6N series 861 applications.SpecificationsPart Number: 5-92XBrand: UDSSeries: L6NCap Diameter: 0.971″Width: 1.445″Style: ISRLube: YesApplication: Rockwell L6N series 861When installing the 5-92X, confirm the yoke ear bores accept the 0.971″ cap diameter and the span between ears measures 1.445″. The ISR retention style uses internal snap rings; inspect the yoke ear grooves before pressing in new caps. The L6N is a Rockwell series designation used in medium-duty and specialty driveline applications.Cross-reference 5-92X against the Rockwell L6N series 861 catalog specification to confirm cap and width dimensions for your specific application. The small cap diameter (0.971″) places this joint in a lower torque bracket — confirm the series matches the application torque requirements.New to U-joints? See our universal joint guide for styles, snap-ring types, and measuring tips. Show less (-) | Brand: UDS Cap Dia 1: 0.971 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
