Series 1350 is the usual step up from 1310 when torque or shaft speed outgrows the smaller size. A weld yoke is welded directly into the driveshaft tube, so it is sized by the tube it enters as much as by the joint it carries.
28Parts
27In stock
Filters Sort results
Reset Apply
Image | Add | Partn number | Series | Material | Tube Dia & Wall | Butt Dia | Center U-J to Weld | Brand | Notes |
|---|---|---|---|---|---|---|---|---|---|
 | 1350 | STEEL | 3.000X0.083 | 2.844 | 2.000" | UDS | |||
 | 1350 | STEEL | 2.000X0.120" | 1.766 | 1.750" | UDS | |||
 | 1350 | STEEL | 2.500X0.083 | 3.344 | 1.938 | UDS | |||
 | 1350 | STEEL | 3.500x0.095 | 3.321 | 1.840" | SPICER | |||
| | 1350 | STEEL | 2.750X0.083 | 2.594 | 2.000" | UDS | SOLID BUTT - CAN BE TURN DOWN TO 2.000 X 0.125 | ||
 | 1350 | STEEL | 3.500X0.065 | 3.375 | 1.812 | SPICER | |||
| | 1350 | STEEL | 3.000X0.095 | 2.812 | 2.000" | UDS | |||
 | 1350 | ALUMINUM | 4.000X0.125 | 3.757 | 2.375 | UDS | 6061-T6 Aluminum | ||
 | 1350 | STEEL | 3.500X0.083 | 3.344 | 1.840" | UDS | |||
| | 1350 | STEEL | 3.000X0.065 | 2.875 | 2.030 | UDS | |||
| | 1350 | STEEL | 2.750X0.065 | 2.625 | 2.000" | UDS | |||
 | 1350 | STEEL | 2.000X0.120" | 1.766 | 2.125 | UDS | EXTRA THICK EARS | ||
 | 1350 | ALUMINUM | 4.000X0.125 | 3.757 | 2.375 | UDS | |||
 | 1350 | ALUMINUM | 4.757 x 0.125 | 3.000" | UDS | 6061-T6 Aluminum | |||
| | 1350 | ALUMINUM | 4.000X0.083 | 3.855 | 2.125 | UDS | |||
 | 1350 | ALUMINUM | 3.000X0.125 | 2.757 | 2.500" | UDS | |||
 | 1350 | ALUMINUM | 3.500X0.125 | 3.257 | 2.376 | UDS | |||
| | 1350 | ALUMINUM | 4.000X0.083 | 3.844 | 2.375 | UDS | |||
 | 1350 | ALUMINUM | 4.000X0.083 | 3.844 | 1.875 | UDS | |||
| | 1350 | STEEL | 4.000X0.083 | 3.844 | 1.688 | UDS |
The butt diameter of the yoke has to match the inside diameter of your tube. Order by series and by tube outside diameter and wall thickness together.
Weld yokes form the permanent ends of a driveshaft. The yoke butt is machined to slide into the tube bore, and the assembly is welded and then balanced as a unit. Because the joint is permanent, getting the tube match right matters more here than on any bolted or splined component.
Give us the series, the tube outside diameter and the wall thickness. Tube OD alone is not enough, since two tubes of the same outside diameter and different wall thickness have different bores and need different yoke butts.
