Brand:
2-26-347 Weld Tube Yoke 1310 Ser’ , Fits: 1.250 x 0.120 , Butt Dia: 1.020 Inch
$25.63
+50 in stock
Description
The 2-26-347U is a 1310 series weld tube yoke for 1.250in OD driveshaft tube with a 1.020″ butt diameter. Steel construction, ready for custom driveshaft fabrication at Universal Driveshafts.
Full Description
2-26-347U: 1310 Series Weld Tube Yoke -- Drivetrain Component Guide
The drivetrain has no redundant load paths -- every torque-carrying component must perform correctly or the system fails. The 2-26-347U is the weld tube yoke position in that load chain for 1310 series applications, providing tube OD 1.250 x wall 0.120, butt dia 1.020 with forged construction and production-controlled tolerances.
Specification Data
| Specification | Value |
|---|---|
| Series | 1310 |
| Tube OD x Wall | 1.250X0.120 |
| Butt Dia | 1.020 |
| CJ to Weld | 2.000" |
| Material | STEEL |
| Brand | UDS |
| Part Number | 2-26-347U |
Failure Modes and Prevention
A worn weld tube yoke typically presents as vibration at certain speed ranges, a clunk on throttle engagement, or visible play when you grab the driveshaft near the yoke and rock it. Left unaddressed, it accelerates u-joint wear, can score the output shaft seal contact area, and in severe cases causes shaft separation. Replacing the 2-26-347U as part of a scheduled drivetrain refresh -- rather than waiting for failure -- is the lower-cost strategy in the long run.
Fitment Checklist
- Tube od 1.250 x wall 0.120, butt dia 1.020 -- verified against this part before ordering
- Series 1310 u-joint cross in service or on order for this shaft end
- Mating component (output shaft / companion flange) in serviceable condition
- Retaining hardware (snap rings, strap bolts, or flange bolts as applicable) renewed if previously heat-cycled
- Shaft balance acceptable after installation -- road test confirms this
Order the 2-26-347U from Universal Driveshafts today. In-stock items ship fast from our warehouse.
Additional information
| Series | 1310 |
|---|---|
| Tube dia wall | 1.250X0.120 |
| Butt dia | 1.020 |
| Center u j to weld | 2.000″ |
| Partn number | 2-26-347 |
| Material | STEEL |
| Brand | UDS |
More Parts from the same Category
Filters Sort results
Reset Apply
Image | Part # | Part Details | Price | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Weld Yokes (191) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Butt dia 3.810" Center u j to weld 2.969 Material STEEL Partn number 100-28-17 Series SPL90/100 Tube dia wall 4.000X0.095 Brand SPICER | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Butt dia 2.321 Center u j to weld 1.688 Material STEEL Partn number 110679 Series 1310 Tube dia wall 2.500X0.095 Brand UDS Notes Butt Diameter 58.95 mm | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Butt dia 1.571 Center u j to weld 1.625 Material STEEL Notes INFINITI FRONT SHAFT Partn number 1126-1711 Series 9951-22 Tube dia wall 1.750X0.095 Brand UDS | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Butt dia 1.667 Center u j to weld 1.750" Material STEEL Partn number 1226-17 Series 1251 Tube dia wall 1.775X.0.65 Brand UDS | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Butt dia 1.844 Center u j to weld 1.750" Material STEEL Notes FOREIGN Partn number 1226-20 Series 1251 Tube dia wall 2.000X0.083 Brand UDS | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Butt dia 1.875 Center u j to weld 1.750" Material STEEL Notes FOREIGN Partn number 1226-201 Series 1251 Tube dia wall 2.000x0.065 Brand UDS | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Butt dia 2.140" Center u j to weld 1.750" Material STEEL Notes FOREIGN Partn number 1226-22 Series 1251 Tube dia wall 2.370X0.065 Brand UDS | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Butt dia 2.375 Center u j to weld 1.750" Material STEEL Notes FOREIGN Partn number 1226-25 Series 1251 Tube dia wall 2.500X0.065 Brand UDS | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Butt dia 2.375 Center u j to weld 1.375 Material STEEL Notes FOREIGN - HONDA Partn number 1226-251 Series 1251-22 Tube dia wall 2.500X0.065 Brand UDS | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Butt dia 2.400" Center u j to weld 1.750" Material STEEL Notes FOREIGN Partn number 1226-26 Series 1251 Tube dia wall 2.550X0.080 Brand UDS | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
