3-4-6631 – End Yoke – 1.500″ Splines Dia – 1410 Series
$79.83
1 in stock
Description
3-4-6631 — 1410 Series end yoke with 1.500-inch spline bore, 1.812-inch hub, and BS snap ring retention. Drop-in replacement for 1410 Series output shafts.
Full Description
Every driveshaft system is only as strong as its weakest yoke. The 3-4-6631 is a UDS 1410 Series end yoke built to handle the torsional demands of performance applications -- from high-horsepower street builds to off-road rigs that flex the suspension to its limits. With a 1.500" spline interface and precision-machined bearing seats, this yoke transfers power cleanly without the slop that kills U-joints prematurely.
Performance-Grade Construction
The 1410 Series yoke series was developed to handle loads beyond light-duty OEM specifications. The 3-4-6631 carries the full load rating of the 1410 Series system, making it appropriate for high-torque applications including turbocharged and supercharged drivetrains, towing configurations, and competition use.
- Full 1410 Series torque rating -- no derating for special applications
- Precision bearing bores -- eliminate U-joint cap rocking that causes premature wear
- Snap ring style: BS -- positive retention under shock loading
- Hub diameter: 1.812" -- correct registration against diff or transfer case seal
| Specification | Value |
|---|---|
| Series | 1410 Series |
| Spline Diameter | 1.500" |
| Spline Count | 10 |
| Hub Diameter | 1.812" |
| Center U-Joint to End | 3.719" |
| Through Hole Diameter | 2.000" |
| Snap Ring Style | BS |
| Brand | UDS |
Specifications
Performance fitment requires exact dimensional matching. The 3-4-6631 is built to the following specs:
Pairing for Maximum Drivetrain Life
The weakest link in any driveshaft assembly determines its service life. Pairing a fresh 3-4-6631 end yoke with a new 1410 Series U-joint and a properly balanced driveshaft eliminates the three most common failure points. For high-horsepower builds, also inspect the driveshaft tube for straightness and the slip yoke for wear -- replacing a yoke without addressing these components leaves the system vulnerable to the same vibration-induced failure.
Center-to-end measurement of 3.719" must be accounted for when calculating driveshaft operating length after suspension lifts or drivetrain swaps.
Part 3-4-6631 is a UDS product. Universal Driveshafts stocks a complete range of 1410 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
Alternative parts:
Additional information
| Cj to end | 3.719 |
|---|---|
| Hub dia | 1.812 |
| Partn number | 3-4-6631 |
| Series | 1410 |
| Splines count | 10 |
| Splines dia | 1.500″ |
| Style | BS |
| Through hole | 2.000″ |
More Parts from the same Category
Filters Sort results
Reset Apply
Image | Part # | Part Details | Price | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| End Yokes (146) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Bore type splined Cj to end 2.50 Hub dia 1.62 Keyway N/A Series 1000 Through hole 1.20 Bore dia 1.125 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 2.50 Hub dia 2.25 Partn number 10-4-143 Bore dia 1.125 Bore type round Keyway GAP - 0.25 Brand UDS Splines count N/A Style ISR Series 1000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Bore type round Cj to end 2.50 Hub dia 1.62 Keyway GAP - 0.25 Series 1000 Through hole 1.20 Bore dia 938 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 2.900" Hub dia 1.342 Notes USED ON 2 PCS SHAFT FOR SUBARU TO REPLACE THE CENTER CV SECTION Partn number 1204-241U Series 1251 Splines count 22/24 Splines dia 995 Style SR Through hole 1.300" | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 3.312 Hub dia 1.445 Notes USED ON 2 PCS SHAFT FOR SUBARU TO REPLACE THE CENTER CVJ SECTION Partn number 1204-261U Series 1251 Splines count 24/26 Splines dia 1.115 Style SR Through hole 1.300" | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 6.200" Hub dia 3.819 Partn number 131446KS Series SPL250 Splines count 49 Splines dia 2.544 Style BS Through hole 2.672 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 2.750" Hub dia 1.420" Notes FITS STUB: 1453-232 OR 3053-233 Partn number 1404-22 Series 1100 Splines count 22/23 Splines dia 0.990" Style SR Through hole 1.360" | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 3.250" Hub dia 1.420" Notes FITS STUB: 1453-232 OR 3053-233 Partn number 1404-231 Series 1100 Splines count 22/23 Splines dia 0.990" Style SR Through hole 1.800" | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 3.265 Hub dia 1.416 Notes USED ON MERKUR SHAFTS Partn number 1404-261 Series 1100 Splines count 26 Splines dia 1.129 Style SR Through hole 1.824 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 5.590" Hub dia 2.879 Notes COUPLING SHAFT YOKE Partn number 170-4-1271-1 Series SPL170 Splines count 46 Splines dia 2.390" Style BS Through hole 2.750" | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
