3-4-7001-1 – End Yoke – 1480 Series – 1.755″ Splines Dia – 2.500″ Hub Dia
$240.08
0 in stock
Description
3-4-7001-1 — 1480 Series end yoke with 1.755-inch spline bore, 2.500-inch hub, and BS snap ring retention. Drop-in replacement for 1480 Series output shafts.
Full Description
Finding the right end yoke starts with matching the output shaft -- and 3-4-7001-1 is engineered specifically for 1480 Series driveline applications. This UDS end yoke connects your transmission or transfer case output to the driveshaft with dimensional precision that eliminates slop and premature wear.
Dimensional Specifications
Before ordering any end yoke, you must verify the output shaft's spline count and diameter. The 3-4-7001-1 is built around a 1.755-inch spline diameter, 13-spline interface with BS retention. The hub measures 2.500" in diameter, and the center-of-U-joint to end distance is 4.281" -- confirming fit with your specific driveshaft length.
| Specification | Value |
|---|---|
| Series | 1480 Series |
| Spline Diameter | 1.755" |
| Spline Count | 13 |
| Hub Diameter | 2.500" |
| Center U-Joint to End | 4.281" |
| Through Hole Diameter | 2.250" |
| Snap Ring Style | BS |
| Brand | UDS |
Engineering and Material Quality
Every UDS end yoke in the 1480 Series lineup is forged or precision-machined from high-grade steel to withstand the torsional and bending loads of real-world drivetrain operation. Yoke ears are machined to consistent bearing cup bore tolerances so U-joint caps seat without rocking, preventing the micro-movement that leads to premature joint failure.
- Consistent bearing bore dimensions for tight U-joint fit
- Designed to OEM companion flange specifications
- Through hole ID of 2.250" provides clearance for speedometer cables or internal shafts where applicable
- Compatible with standard 1480 Series U-joint caps
Installation Guidance
Installation requires that the output shaft splines are clean and free of corrosion. Apply a light coat of assembly lube to the splines before pressing the yoke into position. Torque the retaining nut to OEM specification -- do not reuse stretch bolts or damaged snap rings. If the snap ring style is BS, confirm that the groove in the output shaft matches this style before installation.
Always balance the driveshaft assembly after replacing end yokes on vehicles driven above 55 mph to prevent vibration.
Part 3-4-7001-1 is a UDS product. Universal Driveshafts stocks a complete range of 1480 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
Additional information
| Cj to end | 4.281 |
|---|---|
| Hub dia | 2.500″ |
| Partn number | 3-4-7001-1 |
| Series | 1480 |
| Splines count | 13 |
| Splines dia | 1.755 |
| Style | BS |
| Through hole | 2.250″ |
More Parts from the same Category
Filters Sort results
Reset Apply
Image | Part # | Part Details | Price | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| End Yokes (146) | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | Bore type splined Cj to end 2.50 Hub dia 1.62 Keyway N/A Series 1000 Through hole 1.20 Bore dia 1.125 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 2.50 Hub dia 2.25 Partn number 10-4-143 Bore dia 1.125 Bore type round Keyway GAP - 0.25 Brand UDS Splines count N/A Style ISR Series 1000 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Bore type round Cj to end 2.50 Hub dia 1.62 Keyway GAP - 0.25 Series 1000 Through hole 1.20 Bore dia 938 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 2.900" Hub dia 1.342 Notes USED ON 2 PCS SHAFT FOR SUBARU TO REPLACE THE CENTER CV SECTION Partn number 1204-241U Series 1251 Splines count 22/24 Splines dia 995 Style SR Through hole 1.300" | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 3.312 Hub dia 1.445 Notes USED ON 2 PCS SHAFT FOR SUBARU TO REPLACE THE CENTER CVJ SECTION Partn number 1204-261U Series 1251 Splines count 24/26 Splines dia 1.115 Style SR Through hole 1.300" | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 6.200" Hub dia 3.819 Partn number 131446KS Series SPL250 Splines count 49 Splines dia 2.544 Style BS Through hole 2.672 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 2.750" Hub dia 1.420" Notes FITS STUB: 1453-232 OR 3053-233 Partn number 1404-22 Series 1100 Splines count 22/23 Splines dia 0.990" Style SR Through hole 1.360" | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 3.250" Hub dia 1.420" Notes FITS STUB: 1453-232 OR 3053-233 Partn number 1404-231 Series 1100 Splines count 22/23 Splines dia 0.990" Style SR Through hole 1.800" | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 3.265 Hub dia 1.416 Notes USED ON MERKUR SHAFTS Partn number 1404-261 Series 1100 Splines count 26 Splines dia 1.129 Style SR Through hole 1.824 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| | Cj to end 5.590" Hub dia 2.879 Notes COUPLING SHAFT YOKE Partn number 170-4-1271-1 Series SPL170 Splines count 46 Splines dia 2.390" Style BS Through hole 2.750" | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
