Part No. 3103-23 (also written 3103/23) This 1310 Transmission Yoke Fits Toyota & Lexus Automatic Transmissions from as early as 1989 until 2000 (Cressida, SC300)
In stock3 ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3103-23 · 1310 Series Transmission Yoke
- Part number
- 3103-23
- Part type
- Transmission Yoke
- Condition
- New
- Series
- 1310
- Counter bore diameter
- 0
- Center u-joint to end
- 5.750
- Hub diameter
- 1.575
- Splines count diameter
- 23 X 1.201
- Weight
- 2.44 lb
Fitment
Toyota applications.
1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Interchange / cross-reference
- 3103-23-01
3103-23 replaces or interchanges with 3103-23-01. Cross-reference numbers are supplied for identification; compare the series, spline and bolt-pattern dimensions above before substituting.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
Alternative parts for 3103-23
Same fitment, another number or brand. Check the notes before you substitute.
| Add | Pic | Part # | Price | Series | Hub Dia | Splines Count & Dia | Center U-Joint to End | Counter Bore Dia | Notes |
|---|---|---|---|---|---|---|---|---|---|
![]() |
3103-23S |
$78.46
|
1310 | 1.575 | 23 X 1.201 | 5.750 | 0 | MAZDA RX8 AUTO, machined shoulder off hub |
About 3103-23
The 3103-23 covers Toyota and Lexus rear-wheel-drive automatic transmissions produced from approximately 1989 through 2000, including the Cressida, SC300, and related platforms. Toyota's A-series automatic output shafts in this period used a 23-spline, 1.201" pitch diameter specification -- the same tooth count as the Mazda RX-8 but with a different hub profile (no shoulder removal required on this version).
- 23-spline x 1.201" PD -- Toyota/Lexus A-series automatic; different from Toyota truck manual spec
- 1.575" hub OD -- source tailshaft seal by this dimension; Toyota factory seals are typically 1.575" ID
- 5.750" C-to-end -- stock driveshaft length for Cressida and SC300 rear-drive platforms
- No counterbore -- flat seating face; inspect seal housing for burrs before installation
- Pairs with 1310-series U-joint; replace both joint and yoke as a set on high-mileage vehicles
Tip: the SC300 and Cressida use different driveshaft tube diameters despite sharing the yoke spec -- confirm tube OD before ordering a replacement shaft. The yoke (3103-23) is identical for both, but the tube and rear yoke differ. The transmission yoke is the common first point of failure on high-mileage Toyota RWD platforms due to spline wear from insufficient lubrication.
Related Transmission Yokes in the 1310 series
See the full table
3103-10
Transmission Yokes, 1310 Series, 10 x 1.375 Splines, 2.125" Hub Dia
$65.98In stock
3103-11
Transmission Yokes, 1310 Series, 10 x 1.375 Splines, 2.125" Hub Dia
$76.89In stock
3103-12
Transmission Yokes, 1310 Series, 10 x 1.375 Splines, 2.125" Hub Dia
$94.11In stock
3103-163
Used on Powerglide transmissions which were on early Chevrolet passeng...
$95.03Call
3103-21
1310 Toyota Transmission Yoke fits passenger cars and trucks from Toyo...
$156.93In stock
3103-211
1310 Toyota 20/21 Splines Transmission Yoke fits passenger cars and tr...
$76.99In stock
3103-23S
MAZDA RX8 AUTO, machined shoulder off hub Transmission Yoke 1310
$78.46In stock
3103-24
Transmission Yoke 1310 Nissan Automatic & Manual Transmissions It Is U...
$91.65In stock
3103-23 questions
What series is 3103-23?
3103-23 is a 1310 series transmission yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 3103-23 have?
3103-23 is cut for 23 X 1.201 splines (count × major diameter). Count the splines on the output shaft and measure across the major diameter to confirm.
What part numbers does 3103-23 replace?
3103-23 cross-references to 3103-23-01. Interchange data is for reference; compare the dimensions before substituting.
Is 3103-23 in stock?
Yes. 3 are in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.