Part No. 3103-163 (also written 3103/163) Used on Powerglide transmissions which were on early Chevrolet passenger cars
Call for availability
Stock varies on this part. Call (813) 524-6491 and we will check.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3103-163 · 1310 Series Transmission Yoke
- Part number
- 3103-163
- Part type
- Transmission Yoke
- Condition
- New
- Series
- 1310
- Center u-joint to end
- 4.875
- Counter bore diameter
- 1.156
- Hub diameter
- 1.500
- Splines count diameter
- 16 X 1.172
- Weight
- 5 lb
Fitment
Used on Powerglide transmissions . Same as 2-3-1331X
1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Interchange / cross-reference
- 3103-163-01
3103-163 replaces or interchanges with 3103-163-01. Cross-reference numbers are supplied for identification; compare the series, spline and bolt-pattern dimensions above before substituting.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 3103-163
| Attribute | Specification |
|---|---|
| Part Number | 3103-163 |
| Series | 1310 (1.062" cap diameter) |
| Splines | 16 x 1.375" |
| Hub Diameter | 1.500" |
| Counterbore Diameter | 1.156" |
| Center U-Joint to End | 4.875" |
| Application | Early Chevrolet Powerglide passenger cars |
| Cross-Reference | Spicer 2-3-1331X |
- 16-spline output is unique to early Powerglide units -- not interchangeable with any later GM 26-, 27-, or 32-spline yoke
- 1.156" counterbore pilots over the Powerglide tailshaft bearing retainer; confirm retainer OD before ordering
- 1.500" hub seals against standard GM 1.500" tailshaft seal -- seal is the same as the TH350 seal in bore ID
- 4.875" C-to-end is compact -- these early A-body and full-size Chevrolets used shorter driveshaft tunnels
- Pairs with 1310-series U-joint at 1.062" cap; replaces factory U-bolt or snap-ring joint in this application
Powerglide-equipped early Chevrolets used this yoke across a wide range of body styles. The 16-spline interface is mechanically robust for its era but limits torque capacity compared to later designs -- a consideration if the car has been engine-swapped to a larger displacement powerplant. For high-torque Powerglide builds, inspect the output shaft splines for fretting and consider a custom shaft if spline condition is marginal.
Related Transmission Yokes in the 1310 series
See the full table
3103-10
Transmission Yokes, 1310 Series, 10 x 1.375 Splines, 2.125" Hub Dia
$65.98In stock
3103-11
Transmission Yokes, 1310 Series, 10 x 1.375 Splines, 2.125" Hub Dia
$76.89In stock
3103-12
Transmission Yokes, 1310 Series, 10 x 1.375 Splines, 2.125" Hub Dia
$94.11In stock
3103-21
1310 Toyota Transmission Yoke fits passenger cars and trucks from Toyo...
$156.93In stock
3103-211
1310 Toyota 20/21 Splines Transmission Yoke fits passenger cars and tr...
$76.99In stock
3103-23
This 1310 Transmission Yoke Fits Toyota & Lexus Automatic Transmission...
$84.46In stock
3103-23S
MAZDA RX8 AUTO, machined shoulder off hub Transmission Yoke 1310
$78.46In stock
3103-24
Transmission Yoke 1310 Nissan Automatic & Manual Transmissions It Is U...
$91.65In stock
3103-163 questions
What series is 3103-163?
3103-163 is a 1310 series transmission yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 3103-163 have?
3103-163 is cut for 16 X 1.172 splines (count × major diameter). Count the splines on the output shaft and measure across the major diameter to confirm.
What part numbers does 3103-163 replace?
3103-163 cross-references to 3103-163-01. Interchange data is for reference; compare the dimensions before substituting.