1310 Series Driveshaft Parts
The 1310 is the most common light-duty series: factory on most 1/2-ton pickups, Jeeps, Mustangs and many passenger cars. It shares the 1.062" cap with the 1330 but is narrower. Nominal 1310 dimensions: 1.062" bearing cap diameter, 3.219" snap-ring-to-snap-ring width. Measure the caps on your old joint to confirm the series before ordering.
- 1.062" Cap diameter (nominal)
- 3.219" Width, ring to ring
- 294 Parts in stock
- 18 Categories
-
2-2-479
Flange Yoke 1310 series, 4x 0.438 Holes on 3.750 Bolt Circle Dia...
$14.52 -
2-2-939
Flange Yoke 1310 Series Ford 8.8" and 7.5" Small Bolt Pattern 3....
$17.26 -
2-2-1339
Flange Yoke 1310 series, 6 x 0.441 Holes on 3.307 Bolt Circle Di...
$18.31 -
3102-9048
Flange Yoke 1310, Bolt Circle 2.933,Pilot: 1.850- Flange OD: 90M...
$19.16 -
P2-2-329U
Flange Yokes, 1310 Series, Bolt Circle Dia 3.125", Cj To Flat 1....
$19.33 -
3102-15, 2-2-1679
3102-15 Toyota Flange Yoke 1310 series Square 60 x 60, 2-2-1679,...
$19.40
-
3103-320
1310 Transmission & Transfer Case 2-3-10431X Fits the GM transmi...
$31.32 -
3103-276
Transmission Yoke 1310 26/27 Splines
$59.89 -
2-3-6081X
Transmission Yokes, 1310 Series, 26/27 X 1.176 Splines, 1.500" H...
$60.58 -
3103-10
Transmission Yokes, 1310 Series, 10 x 1.375 Splines, 2.125" Hub...
$65.98 -
3103-277
Transmission Yokes, 1310 Series, 26 / 27 X 1.176 Splines, 1.500"...
$67.17 -
3103-251
Transmission Yoke 1310 Series Fits various 25 spline Ford, Linco...
$67.38
-
2-4-1233
End Yoke - Round Bore 1310 Series, 1.500 Bore KEYWAY: 0.375, Hub...
$18.91 -
2-4-1103
End Yoke 1310 -Round Bore, Bore: 1.375,Keyway 0.312, Hub: 2.000...
$25.37 -
2-4-433
End Yoke - Round Bore 1310 Series, 0.750 Bore KEYWAY: 0.188, Hub...
$29.61 -
2-4-803
End Yoke - Round Bore 1310 Series, 1.375 Bore w/0.375 keyway, 2....
$31.04 -
2-4-3331
End Yoke - Splined Bore 1310 Series, Snap Ring Style, Splines 0....
$35.61 -
3104-321CV
End Yoke CV Conversion To 1310 Jeep JK NP241 07-18, counterbore...
$42.66
-
P211229X
Cv Flange Yoke, Ball Stud Dia 0.5", Bolt Circle Dia 3.5", Bolt H...
$33.99 -
3102-211CV
Cv Flange Yokes, 1310 Series, Ball Stud Dia 0.5", Bolt Circle Di...
$74.05 -
3102-251CV
Cv Flange Yokes, 1310 Series, Ball Stud Dia 0.5", Bolt Circle Di...
$74.05 -
3102-212CV
Cv Flange Yokes, 1310 Series, Ball Stud Dia 0.5", Bolt Circle Di...
$74.05 -
3102-182CV
Cv Flange Yokes, 1310 Series, Ball Stud Dia 0.5", Bolt Circle Di...
$74.05 -
3102-171CV
Cv Flange Yoke, Ball Stud Dia 0.5", Bolt Circle Dia 3.346", Bolt...
$74.05
-
2-28-1757
Weld Tube Yoke 1310 Ser', Fits: 2.000 X 0.120 Butt Dia: 1.766
$11.21 -
2-28-357
Weld Tube Yoke 1310 Series Fits: 2.000 X 0.083
$12.14 -
2-28-417U
Weld Tube Yoke 1310 Series, Fits: 2.000 x 0.065, 1.688 CL to Wel...
$14.42 -
2-28-367
Weld Tube Yoke 1310 Ser', Fits 2.500 x 0.083 Butt Dia: 2.344 Cen...
$16.08 -
2-28-2595
2-28-295 Weld Tube Yoke 1310 Ser', Fits 2.500 x 0.095 Butt Dia:...
$16.08
-
2-28-327
Weld Yokes, 1310 Series, Butt Dia 2.875", Tube Dia Wall 3.000X0....
$16.21
-
2-3-1421KX
Slip Yoke 1310 Series 1.250X16 Centerline to End 5"
$23.68 -
2-3-4951KX
Slip Yoke 1310 series, 1.375x16 spline 6.000 Centerline to End (...
$33.20 -
2-3-8001KX
Slip Yoke, 1310 Series, 1.375" Splines Dia, Center U Joint To En...
$37.17 -
2-3-5821KX
Slip Yoke 1310 series, Splines: 1.375x16 Center Joint To End 7.8...
$39.08 -
2-3-8021KX
Slip Yoke, 1310 Series, 1.375" Splines Dia, Center U Joint To En...
$39.43 -
2-3-128KX
Slip Yoke, 1310 Series, 1.375" Splines Dia, Center U Joint To En...
$39.83
-
2-4-573
End Yoke 1310 - Round Bore, Bore: 1.250, Keyway: 0.25 PTO
$16.76 -
2-4-533
End Yoke 1310 - Round Bore, Bore: 1.188, Keyway: 0.312, Hub Diam...
$19.22 -
2-4-503
End Yoke - Round Bore 1310 series, Bore: 1.125, Keyway: 0.25, Hu...
$22.00 -
2-4-1103
End Yoke 1310 -Round Bore, Bore: 1.375,Keyway 0.312, Hub: 2.000...
$25.37
-
2-4-473
End Yoke, 1310 Series, 1.000" Bore Dia, 2.00" Hub Dia
$33.10 -
2-4-783-1U
PTO End Yoke 1310 Series Hub Dia: 2.125 Bore: 1.250 Keyway: 0.37...
$41.07
-
D3EU-W/O-T-CAP
D3E UDS Brand - Replacement Seals, Non-Threaded Cap Design
$5.50 -
3514-1614U
Dust Caps Threaded, Type Round, Seal Type RUBBER, Num Splines 16...
$17.12 -
D2CU
Dust Caps Threaded, Type Round, Seal Type CORK, Inside Dia 1.652...
$25.04 -
D2MU
Dust Caps Threaded, Type Round, Seal Type RUBBER, Inside Dia 1.6...
$34.19 -
D2NU
Dust Caps Threaded, Type Round, Seal Type RUBBER, Inside Dia 1.7...
$37.93 -
211256XU
Dust Caps Press On, Type Round, Shaft Neck Dia 1.020, Diameter 1...
$110.27
-
2-28-22867
Ball Stud Yokes, 1310 Series, Ball Stud Length Dia 0.500X0.594,...
$35.48
-
2-28-2947
Ball Stud Yoke 1310 Series, Fits Tube 2.000 x 0.120, Butt Dia: 1...
$36.66 -
2-28-2887
Ball Stud Yokes, 1310 Series, Ball Stud Length Dia 0.500X0.594,...
$36.73 -
2-28-2977
Ball Stud Yokes, 1310 Series, Ball Stud Length Dia 0.500X0.594,...
$43.37 -
2-28-3817
Ball Stud Yokes, 1310 Series, Ball Stud Length Dia 0.500X0.594,...
$48.20
-
2-28-2937
Ball Stud Yokes, 1310 Series, Ball Stud Length Dia 0.500X0.594,...
$96.14
-
3182-311
Yoke Shafts, 1310 Series, 1.330" Splines Dia, 31 Spline
$74.53 -
3182-271
Yoke Shafts, 1310 Series, 1.160" Splines Dia, 27 Spline
$94.08 -
3182-322
Yoke Shafts, 1310 Series, 1.378" Splines Dia, 32 Spline
$100.27 -
3182-32
Yoke Shafts, 1310 Series, 1.378" Splines Dia, 32 Spline
$168.69 -
N2-81-1181
Yoke Shafts, 1310 Series, 1.378" Splines dia, 32 Spline
$231.30
-
2-95-29U
U-Joint Lock Straps & Wires, Series 1310
$0.60
-
2-94-28X
U-Bolt Fits 1210/1310/1330 U-Joints
$5.73
-
9553-SF
9533-4724 Unwelded 1310 series - Tube Length: 40"
$96.35
-
9235-SF
Driveshaft, 1310 (1.062 x 3.219) Series, 8.880" Flange To Flange...
$259.14
1310 series questions
What size is a 1310 series u-joint?
A 1310 series universal joint has 1.062" diameter bearing caps and measures 3.219" from snap ring to snap ring (outside of cap to outside of cap). These are nominal figures; measure the caps on your old joint with a caliper to confirm the series.
Is the 1310 series the same as the 1330 or 1210?
No. The 1310 and 1330, 1210 series share the same 1.062" cap diameter but differ in width, so their yokes are not interchangeable. Use a conversion u-joint when you need to join a 1310 yoke to a yoke from a different series.
Which 1310 series parts does UDS stock?
294 1310 series parts across 18 categories: 92 flange yokes, 69 transmission yokes, 33 end yokes, 25 cv flange yokes, 24 weld yokes, 13 slip yoke and more. Everything listed in stock ships the same day from Florida when ordered before 2pm EST.
How do I match 1310 series parts on a driveshaft?
Every u-joint on the shaft must match the yokes it sits in: a 1310 series joint needs 1310 series weld yokes, slip yokes, end yokes or flange yokes (1.062" cap bores). Mixed-series shafts use a conversion joint with a different cap size on each axis.
Other u-joint series
- 1350 · 1.188"
- 1410 · 1.188"
- 1330 · 1.062"
- 1480 · 1.375"
- 1550 · 1.375"
- 3R · 1.125"
- 1710 · 1.938"
- 1000
- 1610 · 1.625"
- 7260 · 1.078"
- 1810 · 2.125"
- 1251
- SPL170
- 1210 · 1.062"
- 1100
- 1760 · 1.938"
- 1751
- 7290 · 1.125"
- SPL90
- SPL250
- 1300
- 1351-20
- SPL100
- SPL140
- 2351-20
- 1330F
- 1880
- 1510
- 1500
- 2351
- 9951-22
- SPL350
- 1485
- 1310HR
- 1351-21
- 1800
- 1551-20
- 1270
- 1310WJ
- 3451
- SPL70
- 2055
- 1555
- 2351-21
Series designations (1310, 1350, 3R, SPL…) are Spicer® / Dana® nomenclature used across the industry and are shown for identification and cross-reference only. Dimensions are nominal; verify fitment before ordering. Copyright & trademark notice