3103-21 1310 Series Transmission Yoke

Part No. 3103-21 (also written 3103/21) 1310 Toyota Transmission Yoke fits passenger cars and trucks from Toyota and Lexus from as early as 1986 until 2007 (Previa, Van, Rav4, Supra, SC300, RX300, Highlander).

$156.93

In stock1 ready to ship

Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.

  • Free shipping on parts orders over $1,000
  • 14-day returns
  • Fitment help: (813) 524-6491

Specifications 3103-21 · 1310 Series Transmission Yoke

How to measurePoint at a letter to read its measurement
BADC
Part number
3103-21
Part type
Transmission Yoke
Condition
New
Series
1310
Hub diameter
1.495
Center u-joint to end
6.000
Counter bore diameter
0
Splines count diameter
20/21 X 1.104
Weight
2.42 lb

Fitment

HIGH VERSION FOR A ONE PIECE SHAFT IS 3103-211, Toyota - typically used on 2pc Toyota truck shaft

1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.

Interchange / cross-reference

3103-21 replaces or interchanges with 3103-211, 2-3-9701X. Cross-reference numbers are supplied for identification; compare the series, spline and bolt-pattern dimensions above before substituting.

Estimate shipping to your ZIP

Estimate shipping

Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.

Local pickup in Florida — free

About 3103-21

Application Note: If you are building a one-piece driveshaft on a Toyota truck platform where the pinion angle is steep, use the 3103-211 high-angle version instead. The standard 3103-21 is correct for two-piece shaft assemblies and low-angle single-piece applications. Using the standard geometry yoke at high operating angles will accelerate U-joint wear and can introduce vibration above 65 mph.

The 3103-21 is the standard replacement transmission yoke for Toyota and Lexus vehicles produced from 1986 through 2007 using a 20/21-spline, 1.104" pitch diameter output shaft. Confirmed fitments include the Previa, Van, Rav4, Supra, SC300, RX300, and Highlander across several transmission variants. The 1.495" hub OD seals against the stock Toyota tailshaft seal. At 6.000" center-to-end, this yoke maintains correct driveshaft geometry at stock suspension height. Cross-reference: Spicer 2-3-9701X. Inspect the output shaft spline tips before installing the new yoke -- Toyota splines are hardened but can develop micro-pitting after 150,000+ miles, which will accelerate wear on the replacement yoke if not addressed first.

Related Transmission Yokes in the 1310 series

See the full table

3103-21 questions

What series is 3103-21?

3103-21 is a 1310 series transmission yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.

What spline count does 3103-21 have?

3103-21 is cut for 20/21 X 1.104 splines (count × major diameter). Count the splines on the output shaft and measure across the major diameter to confirm.

What part numbers does 3103-21 replace?

3103-21 cross-references to 3103-211, 2-3-9701X. Interchange data is for reference; compare the dimensions before substituting.

Is 3103-21 in stock?

Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.