N° de pièce N2-4-JK06 Fourchette d'extrémité, Diam. cannelures 1.25", Diam. moyeu 1.85", 24 cannelures
En stock
La plupart des pièces en stock sont expédiées le jour même pour toute commande passée avant 2pm EST ; les délais de traitement peuvent varier.
- Livraison gratuite pour les commandes de pièces supérieures à $1,000
- Retours sous 14 jours
- Aide à la compatibilité : (813) 524-6491
Spécifications N2-4-JK06 · 1310 Series End Yoke
- Référence de pièce
- N2-4-JK06
- Type de pièce
- Fourchette d'extrémité
- État
- Nouveau
- Série
- 1310
- Style
- UB
- Croisillon à l'extrémité
- 3.000"
- Nombre de cannelures
- 24
- Type d'alésage
- splined
- Diam. de moyeu
- 1.85
- Diam. des cannelures
- 1.25
- Trou traversant
- 1.5
- Poids
- 1.87 lb
Compatibilité
JEEP JK - FRON PINION
Les pièces de la série 1310 utilisent des bonnets de roulement de croisillon de 1.062" avec une largeur circlips à circlips de 3.219" (nominal). Confirmez le diamètre des bols sur la fourche ou le croisillon couplé avant de commander.
Estimez les frais de livraison pour votre code postal
Estimer les frais de port
Tarifs UPS en direct depuis notre atelier en Floride. Commandes de pièces supérieures à $1,000 livraison gratuite — le tube et les arbres de transmission complets sont toujours expédiés au tarif UPS.
Retrait en magasin en Floride — gratuit
À propos de N2-4-JK06
Replacing an end yoke is a straightforward job when you have the right part. The N2-4-JK06 -- a UDS 1310 Series end yoke -- is dimensioned to drop onto the output shaft splines without modification, provided your shaft matches the 1.25" spline diameter and 24-spline count. This guide covers what to check before you order and what to do during installation.
Pre-Order Verification
Before removing your old yoke, record the following from either the old part or the output shaft:
- Spline diameter: Should match 1.25" for this part
- Spline count: Should match 24
- Snap ring style: UB -- check whether the groove is on the inside or outside of the bearing bore
- Series: 1310 Series -- look for the series stamp on the U-joint caps or the original yoke
Application note: JEEP JK - FRON PINION
| Specification | Value |
|---|---|
| Series | 1310 Series |
| Spline Diameter | 1.25" |
| Spline Count | 24 |
| Hub Diameter | 1.85" |
| Center U-Joint to End | 3.000" |
| Through Hole Diameter | 1.5" |
| Snap Ring Style | UB |
| Application Note | JEEP JK - FRON PINION |
| Brand | UDS |
Dimensional Specifications
The N2-4-JK06 carries the following dimensions, which define its fit envelope. Verify each against your application before ordering.
Installation Steps
Once you have confirmed fitment, installation proceeds as follows:
- Remove the old yoke by unthreading the retaining nut and sliding the yoke off the output shaft splines. Mark the driveshaft-to-yoke orientation before disassembly to maintain balance phasing.
- Clean the output shaft splines with a wire brush and solvent. Inspect for cracks or worn spline flanks.
- Apply a thin coat of assembly lubricant to the shaft splines. Do not over-lubricate -- excess grease can cause seal contamination.
- Slide the N2-4-JK06 onto the splines, aligning your reference marks. The hub diameter of 1.85" should register smoothly against the seal bore.
- Install a new snap ring (UB style) in the groove. Confirm it seats fully around the perimeter.
- Torque the retaining nut to the vehicle manufacturer's specification.
After installation, lower the vehicle and drive briefly before inspecting for leaks or vibration. Any vibration at highway speed indicates a balance issue -- have the driveshaft rebalanced with the new yoke installed.
Part N2-4-JK06 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Fourchettes d'extrémité associés de la série 1310
Voir le tableau complet
3104-26CV
Fourchette d'extrémité, série 1310, 26 cannelures, Style CV
$48.27En stock
3104-05
Fourchette d'extrémité, Diam. cannelures 1.188", série 1310, Diam. moy...
$84.60En stock
3104-231
Fourchette d'extrémité, Diam. cannelures 1.26", Diam. moyeu 1.562", 23...
$104.94En stock
3104-02
Fourchette d'extrémité, Diam. cannelures 1.146", Diam. moyeu 1.844", 2...
$99.17En stock
2-4-0523
Fourchette d'extrémité, série 1310, Diam. moyeu 2.125", 2.562" Joint à...
$43.88En stock
2-4-1233
Fourchette d'extrémité - alésage rond série 1310, 1.500 Alésage Rainur...
$18.91En stock
3104-321CV
Fourchette d'extrémité CV Conversion To 1310 Jeep JK NP241 07-18, coun...
$42.66En stock
2-4-2271-1
Fourchette d'extrémité, Diam. cannelures 1.146", Diam. moyeu 1.562", 2...
$107.03En stock
N2-4-JK06 questions
De quelle série est N2-4-JK06 ?
N2-4-JK06 est un élément de la série 1310 Fourchette d'extrémité. Les dimensions nominales de la série 1310 sont des bols de roulement de 1.062" avec une largeur circlips à circlips de 3.219". Mesurez le diamètre des bols de votre ancien croisillon pour confirmer la série avant de commander.
Combien de cannelures possède N2-4-JK06 ?
N2-4-JK06 comporte 24 cannelures sur un diamètre de cannelure de 1.25". Comptez les cannelures sur l'arbre de sortie et mesurez le diamètre extérieur pour confirmer.