2-4-2271-1 1310 Series End Yoke

Part No. 2-4-2271-1 End Yoke, 1.146" Splines Dia, 1.562" Hub Dia, 26 Spline

$107.03

In stock1 ready to ship

Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.

  • Free shipping on parts orders over $1,000
  • 14-day returns
  • Fitment help: (813) 524-6491

Specifications 2-4-2271-1 · 1310 Series End Yoke

How to measurePoint at a letter to read its measurement
ABCFGED
Part number
2-4-2271-1
Part type
End Yoke
Condition
New
Series
1310
Style
BS
Through hole
1.500"
CJ to end
3.000"
Splines count
26
Splines diameter
1.146
Bore type
splined
Hub diameter
1.562
Weight
1.71 lb

Fitment

1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.

Estimate shipping to your ZIP

Estimate shipping

Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.

Local pickup in Florida — free

About 2-4-2271-1

A worn or damaged end yoke is one of the most common causes of driveline vibration and U-joint failure -- yet it's often overlooked during diagnosis. The 2-4-2271-1 from UDS provides a direct, properly dimensioned replacement for 1310 Series applications, restoring the tight tolerances that eliminate vibration at the source.

The Problem: Worn Yoke Geometry

When end yoke bores wear oval or the snap ring groove erodes, U-joint caps begin to rock in their seats. This produces a clicking or clunking noise at low speed, a vibration that tracks with vehicle speed, and -- in severe cases -- catastrophic U-joint ejection. The 2-4-2271-1 replaces the worn geometry with new machined surfaces: 1.146" spline bore, 1.562" hub diameter, bearing bores held to 1310 Series tolerances.

Specification Value
Series 1310 Series
Spline Diameter 1.146"
Spline Count 26
Hub Diameter 1.562"
Center U-Joint to End 3.000"
Through Hole Diameter 1.500"
Snap Ring Style BS
Brand UDS

Specifications That Guarantee Fit

Precision fit starts with matching three numbers: spline count, spline diameter, and snap ring style. The 2-4-2271-1 is built to the following dimensions -- verify each against your output shaft before ordering.

Long-Term Reliability

The UDS manufacturing process subjects each yoke to dimensional inspection before shipment. Bearing bore roundness, spline form, and hub diameter are checked against 1310 Series master gauges. The result is a yoke that installs without hammering, retains U-joint caps securely under high-cycle loading, and seals against output shaft oil seals without leaking.

  • Through hole: 1.500" -- clears internal shafts and cables
  • Center U-joint to end: 3.000" -- maintains correct driveshaft length
  • Snap ring style: BS -- matches OEM retention method
  • Drop-in replacement -- no machining required

Part 2-4-2271-1 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.

New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.

Related End Yokes in the 1310 series

See the full table

2-4-2271-1 questions

What series is 2-4-2271-1?

2-4-2271-1 is a 1310 series end yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.

What spline count does 2-4-2271-1 have?

2-4-2271-1 has 26 splines on a 1.146" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.

Is 2-4-2271-1 in stock?

Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.