Part No. 2-4-2271-1 End Yoke, 1.146" Splines Dia, 1.562" Hub Dia, 26 Spline
In stock1 ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 2-4-2271-1 · 1310 Series End Yoke
- Part number
- 2-4-2271-1
- Part type
- End Yoke
- Condition
- New
- Series
- 1310
- Style
- BS
- Through hole
- 1.500"
- CJ to end
- 3.000"
- Splines count
- 26
- Splines diameter
- 1.146
- Bore type
- splined
- Hub diameter
- 1.562
- Weight
- 1.71 lb
Fitment
1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 2-4-2271-1
A worn or damaged end yoke is one of the most common causes of driveline vibration and U-joint failure -- yet it's often overlooked during diagnosis. The 2-4-2271-1 from UDS provides a direct, properly dimensioned replacement for 1310 Series applications, restoring the tight tolerances that eliminate vibration at the source.
The Problem: Worn Yoke Geometry
When end yoke bores wear oval or the snap ring groove erodes, U-joint caps begin to rock in their seats. This produces a clicking or clunking noise at low speed, a vibration that tracks with vehicle speed, and -- in severe cases -- catastrophic U-joint ejection. The 2-4-2271-1 replaces the worn geometry with new machined surfaces: 1.146" spline bore, 1.562" hub diameter, bearing bores held to 1310 Series tolerances.
| Specification | Value |
|---|---|
| Series | 1310 Series |
| Spline Diameter | 1.146" |
| Spline Count | 26 |
| Hub Diameter | 1.562" |
| Center U-Joint to End | 3.000" |
| Through Hole Diameter | 1.500" |
| Snap Ring Style | BS |
| Brand | UDS |
Specifications That Guarantee Fit
Precision fit starts with matching three numbers: spline count, spline diameter, and snap ring style. The 2-4-2271-1 is built to the following dimensions -- verify each against your output shaft before ordering.
Long-Term Reliability
The UDS manufacturing process subjects each yoke to dimensional inspection before shipment. Bearing bore roundness, spline form, and hub diameter are checked against 1310 Series master gauges. The result is a yoke that installs without hammering, retains U-joint caps securely under high-cycle loading, and seals against output shaft oil seals without leaking.
- Through hole: 1.500" -- clears internal shafts and cables
- Center U-joint to end: 3.000" -- maintains correct driveshaft length
- Snap ring style: BS -- matches OEM retention method
- Drop-in replacement -- no machining required
Part 2-4-2271-1 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Related End Yokes in the 1310 series
See the full table
3104-26CV
End Yoke, 1310 Series, 26 Splines, Style CV
$48.27In stock
3104-05
End Yoke, 1.188" Splines Dia, 1310 Series, 1.521" Hub Dia
$84.60In stock
3104-231
End Yoke, 1.26" Splines Dia, 1.562" Hub Dia, 23 Spline
$104.94In stock
3104-02
End Yoke, 1.146" Splines Dia, 1.844" Hub Dia, 26 Spline
$99.17In stock
2-4-0523
End Yoke, 1310 Series, 2.125" Hub Dia, 2.562" Cj To End
$43.88In stock
2-4-1233
End Yoke - Round Bore 1310 Series, 1.500 Bore KEYWAY: 0.375, Hub Diame...
$18.91In stock
N2-4-JK06
End Yoke, 1.25" Splines dia, 1.85" Hub Dia, 24 Spline
$115.63In stock
3104-321CV
End Yoke CV Conversion To 1310 Jeep JK NP241 07-18, counterbore by nut...
$42.66In stock
2-4-2271-1 questions
What series is 2-4-2271-1?
2-4-2271-1 is a 1310 series end yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 2-4-2271-1 have?
2-4-2271-1 has 26 splines on a 1.146" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.
Is 2-4-2271-1 in stock?
Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.