Part No. N2-4-JK06 End Yoke, 1.25" Splines dia, 1.85" Hub Dia, 24 Spline
In stock
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications N2-4-JK06 · 1310 Series End Yoke
- Part number
- N2-4-JK06
- Part type
- End Yoke
- Condition
- New
- Series
- 1310
- Style
- UB
- CJ to end
- 3.000"
- Splines count
- 24
- Bore type
- splined
- Hub diameter
- 1.85
- Splines diameter
- 1.25
- Through hole
- 1.5
- Weight
- 1.87 lb
Fitment
JEEP JK - FRON PINION
1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About N2-4-JK06
Replacing an end yoke is a straightforward job when you have the right part. The N2-4-JK06 -- a UDS 1310 Series end yoke -- is dimensioned to drop onto the output shaft splines without modification, provided your shaft matches the 1.25" spline diameter and 24-spline count. This guide covers what to check before you order and what to do during installation.
Pre-Order Verification
Before removing your old yoke, record the following from either the old part or the output shaft:
- Spline diameter: Should match 1.25" for this part
- Spline count: Should match 24
- Snap ring style: UB -- check whether the groove is on the inside or outside of the bearing bore
- Series: 1310 Series -- look for the series stamp on the U-joint caps or the original yoke
Application note: JEEP JK - FRON PINION
| Specification | Value |
|---|---|
| Series | 1310 Series |
| Spline Diameter | 1.25" |
| Spline Count | 24 |
| Hub Diameter | 1.85" |
| Center U-Joint to End | 3.000" |
| Through Hole Diameter | 1.5" |
| Snap Ring Style | UB |
| Application Note | JEEP JK - FRON PINION |
| Brand | UDS |
Dimensional Specifications
The N2-4-JK06 carries the following dimensions, which define its fit envelope. Verify each against your application before ordering.
Installation Steps
Once you have confirmed fitment, installation proceeds as follows:
- Remove the old yoke by unthreading the retaining nut and sliding the yoke off the output shaft splines. Mark the driveshaft-to-yoke orientation before disassembly to maintain balance phasing.
- Clean the output shaft splines with a wire brush and solvent. Inspect for cracks or worn spline flanks.
- Apply a thin coat of assembly lubricant to the shaft splines. Do not over-lubricate -- excess grease can cause seal contamination.
- Slide the N2-4-JK06 onto the splines, aligning your reference marks. The hub diameter of 1.85" should register smoothly against the seal bore.
- Install a new snap ring (UB style) in the groove. Confirm it seats fully around the perimeter.
- Torque the retaining nut to the vehicle manufacturer's specification.
After installation, lower the vehicle and drive briefly before inspecting for leaks or vibration. Any vibration at highway speed indicates a balance issue -- have the driveshaft rebalanced with the new yoke installed.
Part N2-4-JK06 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Related End Yokes in the 1310 series
See the full table
3104-26CV
End Yoke, 1310 Series, 26 Splines, Style CV
$48.27In stock
3104-05
End Yoke, 1.188" Splines Dia, 1310 Series, 1.521" Hub Dia
$84.60In stock
3104-231
End Yoke, 1.26" Splines Dia, 1.562" Hub Dia, 23 Spline
$104.94In stock
3104-02
End Yoke, 1.146" Splines Dia, 1.844" Hub Dia, 26 Spline
$99.17In stock
2-4-0523
End Yoke, 1310 Series, 2.125" Hub Dia, 2.562" Cj To End
$43.88In stock
2-4-1233
End Yoke - Round Bore 1310 Series, 1.500 Bore KEYWAY: 0.375, Hub Diame...
$18.91In stock
3104-321CV
End Yoke CV Conversion To 1310 Jeep JK NP241 07-18, counterbore by nut...
$42.66In stock
2-4-2271-1
End Yoke, 1.146" Splines Dia, 1.562" Hub Dia, 26 Spline
$107.03In stock
N2-4-JK06 questions
What series is N2-4-JK06?
N2-4-JK06 is a 1310 series end yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does N2-4-JK06 have?
N2-4-JK06 has 24 splines on a 1.25" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.