N2-4-JK06 1310 Series End Yoke

N.º de parte N2-4-JK06 Yugo de extremo, Diám. de estrías 1.25", Diám. de cubo 1.85", 24 estrías

$115.63

En stock

La mayoría de las piezas en stock salen el mismo día si se piden antes de las 2pm EST; los tiempos de procesamiento pueden variar.

  • Envío gratis en pedidos de piezas de más de $1,000
  • Devoluciones en 14 días
  • Ayuda con la compatibilidad: (813) 524-6491

Especificaciones N2-4-JK06 · 1310 Series End Yoke

Cómo medirSeñala una letra para ver su medida
ABCFGED
Número de pieza
N2-4-JK06
Tipo de pieza
Yugo de extremo
Condición
Nuevo
Serie
1310
Estilo
UB
Cruceta a extremo
3.000"
Cantidad de estrías
24
Tipo de orificio
splined
Diám. de cubo
1.85
Diám. de estrías
1.25
Agujero pasante
1.5
Peso
1.87 lb

Compatibilidad

JEEP JK - FRON PINION

Las piezas de serie 1310 usan copas de rodamiento de cruceta de 1.062" con un ancho de 3.219" de anillo a anillo (nominal). Confirma el diámetro de copa en el yugo o la cruceta que acopla antes de comprar.

Calcula el envío a tu código postal

Calcular envío

Tarifas UPS en vivo desde nuestro taller en Florida. Los pedidos de piezas de más de $1,000 tienen envío gratis; el tubo y los cardanes completos siempre se envían con la tarifa UPS.

Retiro en tienda en Florida: gratis

Acerca de N2-4-JK06

Replacing an end yoke is a straightforward job when you have the right part. The N2-4-JK06 -- a UDS 1310 Series end yoke -- is dimensioned to drop onto the output shaft splines without modification, provided your shaft matches the 1.25" spline diameter and 24-spline count. This guide covers what to check before you order and what to do during installation.

Pre-Order Verification

Before removing your old yoke, record the following from either the old part or the output shaft:

  • Spline diameter: Should match 1.25" for this part
  • Spline count: Should match 24
  • Snap ring style: UB -- check whether the groove is on the inside or outside of the bearing bore
  • Series: 1310 Series -- look for the series stamp on the U-joint caps or the original yoke

Application note: JEEP JK - FRON PINION

Specification Value
Series 1310 Series
Spline Diameter 1.25"
Spline Count 24
Hub Diameter 1.85"
Center U-Joint to End 3.000"
Through Hole Diameter 1.5"
Snap Ring Style UB
Application Note JEEP JK - FRON PINION
Brand UDS

Dimensional Specifications

The N2-4-JK06 carries the following dimensions, which define its fit envelope. Verify each against your application before ordering.

Installation Steps

Once you have confirmed fitment, installation proceeds as follows:

  1. Remove the old yoke by unthreading the retaining nut and sliding the yoke off the output shaft splines. Mark the driveshaft-to-yoke orientation before disassembly to maintain balance phasing.
  2. Clean the output shaft splines with a wire brush and solvent. Inspect for cracks or worn spline flanks.
  3. Apply a thin coat of assembly lubricant to the shaft splines. Do not over-lubricate -- excess grease can cause seal contamination.
  4. Slide the N2-4-JK06 onto the splines, aligning your reference marks. The hub diameter of 1.85" should register smoothly against the seal bore.
  5. Install a new snap ring (UB style) in the groove. Confirm it seats fully around the perimeter.
  6. Torque the retaining nut to the vehicle manufacturer's specification.

After installation, lower the vehicle and drive briefly before inspecting for leaks or vibration. Any vibration at highway speed indicates a balance issue -- have the driveshaft rebalanced with the new yoke installed.

Part N2-4-JK06 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.

New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.

Yugos de extremo relacionados de la serie 1310

Ver la tabla completa

N2-4-JK06 preguntas

¿De qué serie es N2-4-JK06?

N2-4-JK06 pertenece a la serie 1310 (Yugo de extremo). Las dimensiones nominales de la serie 1310 son copas de 1.062" con un ancho de 3.219" de anillo a anillo. Mide el diámetro de copa de tu cruceta vieja para confirmar la serie antes de comprar.

¿Cuántas estrías tiene N2-4-JK06?

N2-4-JK06 tiene 24 estrías en un diámetro de estrías de 1.25". Cuenta las estrías del eje de salida y mide el diámetro mayor para confirmar.

Esta traducción fue hecha con IA y puede contener errores. Si algo no queda claro, llame al (813) 524-6491 o cambie a inglés.