部品番号 1253-261 (別表記 1253/261) スタブミッドシップシャフト, 26 x 1.115 スプライン, バット径 2.375", チューブ外径・肉厚 2.500X0.065
在庫あり1 件の出荷準備完了
在庫品の多くは 2pm(EST)までのご注文で当日発送いたします。処理時間は前後する場合があります。
- 部品注文の送料無料金額 $1,000
- 14日以内返品可能
- 適合に関するサポート: (813) 524-6491
仕様 1253-261 · Stub Shaft
- 部品番号
- 1253-261
- パーツタイプ
- Stub Shaft
- 状態
- 新品
- スタイル
- FIXED
- チューブ肉厚
- 0.065"
- チューブ径
- 2.500
- バット径
- 2.375
- 端部から溶接部まで
- 3.125
- スプライン数と径
- 26 x 1.115
- スプラインの長さ
- 1.120
- 重量
- 2.04 lb
適合性
USE WITH: 1204-261 , Uses 858018 nut
互換品 / クロスレファレンス
- 1253-261-01
1253-261 は 1253-261-01 と互換性があります。相互参照番号は識別用です。交換前に、上記のシリーズ、スプライン、ボルトパターンの寸法をご確認ください。
郵便番号への送料を見積もる
送料を計算
フロリダの弊社ショップからのリアルタイム UPS 送料。パーツのご注文が $1,000 送料無料 — チューブおよび完全なプロペラシャフトは常にUPSの料金で発送されます。
フロリダでの店頭受取 — 無料
1253-261 について
The 1253-261 stub midship shaft bridges the gap between transmission output and rear driveshaft section in two-piece driveshaft assemblies. Featuring 26 x 1.115 splines, a 2.375" butt diameter, and a 2.500" x 0.065" wall tube, it is precision-welded to maintain driveline balance within tight tolerances.
Two-Piece Driveshaft Architecture
Long-wheelbase trucks and SUVs use a two-piece driveshaft to avoid resonance frequencies that would be unavoidable with a single long tube. The front section -- the stub midship -- rides on a center support bearing and connects to the front of the rear driveshaft section. The 1253-261 fills this role, providing a dimensionally stable, balanced midship tube ready for installation with a matching center support bearing.
Dimensional Specifications
| Parameter | Value |
|---|---|
| Part Number | 1253-261 |
| Splines Count x Dia. | 26 x 1.115" |
| Spline Length | 1.120" (approx.) |
| Butt Diameter | 2.375" |
| Tube Diameter | 2.500" |
| Tube Wall | 0.065" |
| End-to-Weld Dimension | 3.125" |
Balance and Runout Standards
Midship shafts are finish-balanced after assembly. Runout should be verified at installation: use a dial indicator at the center of the tube with the shaft supported on its U-joints. Maximum allowable TIR is 0.010" for passenger and light truck applications. Any damage to the tube that causes runout exceeding this limit requires replacement.
Installation Guidance
- Install center support bearing before raising shaft into position
- Align spline pilot into transmission or transfer case output bore
- Mate rear U-joint cross into the rear yoke with snap rings fully seated
- Torque center support bearing bracket fasteners to specification
- Check driveshaft angle: improper center bearing height causes vibration
Ordering
Universal Driveshafts stocks stub midship shafts across a wide range of spline and tube configurations. The 1253-261 ships assembled and ready to install. Pair with a matching center support bearing from our catalog for a complete two-piece driveshaft solution.
関連する Stub & Midship Shaft
全一覧表を見る
1253-242
1253-242
$59.95在庫あり
1340-20
スタブミッドシップシャフト, 20 X 1.310 スプライン, バット径 2.435", エ...
$59.82在庫あり
1340-20L
スタブミッドシップシャフト, 20 X 1.310 スプライン, バット径 2.435", チ...
$109.16在庫あり
1340-21
スタブミッドシップシャフト, 20 X 1.310 スプライン, バット径 2.435", チ...
$73.13在庫あり
1442-17
Stub & Midship Shaft, 16 X 1.063 スプライン, バット径 1.625", チューブ...
$84.04在庫あり
1442-20
Stub & Midship Shaft, 16 X 1.063 スプライン, バット径 1.875", チューブ...
$48.54在庫あり
1442-202
スタブミッドシップシャフト, 20 X 0.853 スプライン, バット径 1.875", チ...
$58.69在庫あり
1442-209
スタブミッドシップシャフト, 16 X 1.063 スプライン, バット径 1.812", チ...
$48.50在庫あり
1253-261 ご質問
1253-261 のスプライン数はいくつですか?
1253-261 はスプライン 26 x 1.115(山数 × 外径)用に加工されています。 出力シャフトのスプライン数を数え、外径(最大径)を測って確認してください。
1253-261 はどの部品番号の代替品ですか?
1253-261 は 1253-261-01 とクロスリファレンス対応しています。互換データは参考情報です。交換前に寸法をご確認ください。
1253-261 の在庫はありますか?
はい。フロリダ州に 1 点の在庫がございます。平日の東部標準時(EST)午後2時までのご注文の多くは、当日中に発送いたします。