N.º de parte 1253-261 (también escrito 1253/261) Eje intermedio (stub), 26 x 1.115 estrías, Diám. de asiento 2.375", Diám. × pared de tubo 2.500X0.065
En stock1 listos para enviar
La mayoría de las piezas en stock salen el mismo día si se piden antes de las 2pm EST; los tiempos de procesamiento pueden variar.
- Envío gratis en pedidos de piezas de más de $1,000
- Devoluciones en 14 días
- Ayuda con la compatibilidad: (813) 524-6491
Especificaciones 1253-261 · Stub Shaft
- Número de pieza
- 1253-261
- Tipo de pieza
- Stub Shaft
- Condición
- Nuevo
- Estilo
- FIXED
- Pared de tubo
- 0.065"
- Diámetro de tubo
- 2.500
- Diámetro de asiento
- 2.375
- Extremo a soldadura
- 3.125
- Cantidad y diám. de estrías
- 26 x 1.115
- Largo de estrías
- 1.120
- Peso
- 2.04 lb
Compatibilidad
USE WITH: 1204-261 , Uses 858018 nut
Intercambio / referencia cruzada
- 1253-261-01
1253-261 reemplaza o intercambia con 1253-261-01. Los números de referencia cruzada son para identificación; compara la serie, las estrías y el patrón de pernos de arriba antes de sustituir.
Calcula el envío a tu código postal
Calcular envío
Tarifas UPS en vivo desde nuestro taller en Florida. Los pedidos de piezas de más de $1,000 tienen envío gratis; el tubo y los cardanes completos siempre se envían con la tarifa UPS.
Retiro en tienda en Florida: gratis
Acerca de 1253-261
The 1253-261 stub midship shaft bridges the gap between transmission output and rear driveshaft section in two-piece driveshaft assemblies. Featuring 26 x 1.115 splines, a 2.375" butt diameter, and a 2.500" x 0.065" wall tube, it is precision-welded to maintain driveline balance within tight tolerances.
Two-Piece Driveshaft Architecture
Long-wheelbase trucks and SUVs use a two-piece driveshaft to avoid resonance frequencies that would be unavoidable with a single long tube. The front section -- the stub midship -- rides on a center support bearing and connects to the front of the rear driveshaft section. The 1253-261 fills this role, providing a dimensionally stable, balanced midship tube ready for installation with a matching center support bearing.
Dimensional Specifications
| Parameter | Value |
|---|---|
| Part Number | 1253-261 |
| Splines Count x Dia. | 26 x 1.115" |
| Spline Length | 1.120" (approx.) |
| Butt Diameter | 2.375" |
| Tube Diameter | 2.500" |
| Tube Wall | 0.065" |
| End-to-Weld Dimension | 3.125" |
Balance and Runout Standards
Midship shafts are finish-balanced after assembly. Runout should be verified at installation: use a dial indicator at the center of the tube with the shaft supported on its U-joints. Maximum allowable TIR is 0.010" for passenger and light truck applications. Any damage to the tube that causes runout exceeding this limit requires replacement.
Installation Guidance
- Install center support bearing before raising shaft into position
- Align spline pilot into transmission or transfer case output bore
- Mate rear U-joint cross into the rear yoke with snap rings fully seated
- Torque center support bearing bracket fasteners to specification
- Check driveshaft angle: improper center bearing height causes vibration
Ordering
Universal Driveshafts stocks stub midship shafts across a wide range of spline and tube configurations. The 1253-261 ships assembled and ready to install. Pair with a matching center support bearing from our catalog for a complete two-piece driveshaft solution.
Stub & Midship Shaft relacionados
Ver la tabla completa
1253-242
1253-242
$59.95En stock
1340-20
Eje intermedio (stub), 20 X 1.310 estrías, Diám. de asiento 2.435", Ex...
$59.82En stock
1340-20L
Eje intermedio (stub), 20 X 1.310 estrías, Diám. de asiento 2.435", Di...
$109.16En stock
1340-21
Eje intermedio (stub), 20 X 1.310 estrías, Diám. de asiento 2.435", Di...
$73.13En stock
1442-17
Stub & Midship Shaft, 16 X 1.063 estrías, Diám. de asiento 1.625", Diá...
$84.04En stock
1442-20
Stub & Midship Shaft, 16 X 1.063 estrías, Diám. de asiento 1.875", Diá...
$48.54En stock
1442-202
Eje intermedio (stub), 20 X 0.853 estrías, Diám. de asiento 1.875", Di...
$58.69En stock
1442-209
Eje intermedio (stub), 16 X 1.063 estrías, Diám. de asiento 1.812", Di...
$48.50En stock
1253-261 preguntas
¿Cuántas estrías tiene 1253-261?
1253-261 está cortado para estrías 26 x 1.115 (cantidad × diámetro mayor). Cuenta las estrías del eje de salida y mide el diámetro mayor para confirmar.
¿Qué números de parte reemplaza 1253-261?
1253-261 tiene referencia cruzada con 1253-261-01. Los datos de intercambio son de referencia; compara las dimensiones antes de sustituir.
¿Hay 1253-261 en existencia?
Sí. Hay 1 en existencia en Florida. La mayoría de los pedidos hechos antes de las 2 p. m. EST en día hábil salen el mismo día.