Part No. 1253-242 (also written 1253/242) 1253-242
In stock
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 1253-242 · Stub Shaft
- Part number
- 1253-242
- Part type
- Stub Shaft
- Condition
- New
- Style
- FIXED
- Tube diameter
- 2.000
- Tube wall
- 0.065"
- Butt diameter
- 1.875
- End to weld
- 2.875
- Splines count diameter
- 24 x 0.995
- Length
- 1.180
- Bearing diameter
- 0.985
- Weight
- 1.58 lb
Fitment
use is with : 1204-241 nut sold sepratly: 858018
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 1253-242
The 1253-242 stub shaft or midship shaft is a critical intermediate driveline component used in multi-piece shaft assemblies. With a 1.875-inch butt diameter and 24 x 0.995 spline engagement, it connects the front and rear shaft sections while carrying the center support bearing journal that holds the midshaft in alignment with the vehicle's chassis tunnel.
Dimensional Specifications
| Parameter | Value |
|---|---|
| Style | FIXED |
| Butt Diameter | 1.875" |
| Splines Count x Dia | 24 x 0.995 |
| End to Weld | 2.875" |
| Tube Diameter | 2.000" |
| Tube Wall | 0.065" |
| Bearing Diameter | 0.985" |
| Length | 1.180" |
| Notes | use is with : 1204-241 nut sold sepratly: 858018 |
| Part Number | 1253-242 |
Multi-Piece Driveshaft Architecture
Long-wheelbase trucks and commercial vehicles use two-piece or three-piece driveshafts to avoid the critical whirl speed problem that occurs when a single long shaft is rotated at high RPM. The stub or midship shaft is the intermediate member of this assembly, supported at its midpoint by the center carrier bearing and connected to the rear shaft section at its output end. The bearing journal diameter -- 0.985 inches on the 1253-242 -- must match the carrier bearing's bore for correct fit and concentricity.
Installation and Alignment
- The center support bearing must be shimmed or adjusted so the stub shaft centerline aligns with the front and rear shaft segments -- misalignment of even 1-2mm introduces a permanent operating angle that causes vibration
- Confirm the spline engagement (24 x 0.995) is compatible with the mating nut or coupling specified in the notes: use is with : 1204-241 nut sold sepratly: 858018
- Torque the end nut to specification and verify with a calibrated torque wrench
- After assembly, dynamically balance the complete two-piece assembly on a driveshaft balancer for best NVH results
Specialist Stock at Universal Driveshafts
The 1253-242 midship shaft is a specialized component stocked for direct-replacement applications. Our driveline engineers can cross-reference superseded part numbers and confirm fitment for your specific vehicle and build configuration.
Related Stub & Midship Shaft
See the full table
1253-261
Stub Midship Shaft, 26 x 1.115 Splines, Butt Dia 2.375", Tube Dia Wall...
$59.95In stock
1340-20
Stub Midship Shaft, 20 X 1.310 Splines, Butt Dia 2.435", End To Weld 7...
$59.82In stock
1340-20L
Stub Midship Shaft, 20 X 1.310 Splines, Butt Dia 2.435", Tube Dia Wall...
$109.16In stock
1340-21
Stub Midship Shaft, 20 X 1.310 Splines, Butt Dia 2.435", Tube Dia Wall...
$73.13In stock
1442-17
Stub & Midship Shaft, 16 X 1.063 Splines, Butt Dia 1.625", Tube Dia Wa...
$84.04In stock
1442-20
Stub & Midship Shaft, 16 X 1.063 Splines, Butt Dia 1.875", Tube Dia 2....
$48.54In stock
1442-202
Stub Midship Shaft, 20 X 0.853 Splines, Butt Dia 1.875", Tube Dia Wall...
$58.69In stock
1442-209
Stub Midship Shaft, 16 X 1.063 Splines, Butt Dia 1.812", Tube Dia 2.00...
$48.50In stock
1253-242 questions
What spline count does 1253-242 have?
1253-242 is cut for 24 x 0.995 splines (count × major diameter). Count the splines on the output shaft and measure across the major diameter to confirm.