1253-261 Stub Shaft
FIXED

Part No. 1253-261 (also written 1253/261) Stub Midship Shaft, 26 x 1.115 Splines, Butt Dia 2.375", Tube Dia Wall 2.500X0.065

$59.95

In stock1 ready to ship

Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.

  • Free shipping on parts orders over $1,000
  • 14-day returns
  • Fitment help: (813) 524-6491

Specifications 1253-261 · Stub Shaft

How to measurePoint at a letter to read its measurement
EBADFC
Part number
1253-261
Part type
Stub Shaft
Condition
New
Style
FIXED
Tube wall
0.065"
Tube diameter
2.500
Butt diameter
2.375
End to weld
3.125
Splines count diameter
26 x 1.115
Splines length
1.120
Weight
2.04 lb

Fitment

USE WITH: 1204-261 , Uses 858018 nut

Interchange / cross-reference

  • 1253-261-01

1253-261 replaces or interchanges with 1253-261-01. Cross-reference numbers are supplied for identification; compare the series, spline and bolt-pattern dimensions above before substituting.

Estimate shipping to your ZIP

Estimate shipping

Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.

Local pickup in Florida — free

About 1253-261

The 1253-261 stub midship shaft bridges the gap between transmission output and rear driveshaft section in two-piece driveshaft assemblies. Featuring 26 x 1.115 splines, a 2.375" butt diameter, and a 2.500" x 0.065" wall tube, it is precision-welded to maintain driveline balance within tight tolerances.

Two-Piece Driveshaft Architecture

Long-wheelbase trucks and SUVs use a two-piece driveshaft to avoid resonance frequencies that would be unavoidable with a single long tube. The front section -- the stub midship -- rides on a center support bearing and connects to the front of the rear driveshaft section. The 1253-261 fills this role, providing a dimensionally stable, balanced midship tube ready for installation with a matching center support bearing.

Dimensional Specifications

ParameterValue
Part Number1253-261
Splines Count x Dia.26 x 1.115"
Spline Length1.120" (approx.)
Butt Diameter2.375"
Tube Diameter2.500"
Tube Wall0.065"
End-to-Weld Dimension3.125"

Balance and Runout Standards

Midship shafts are finish-balanced after assembly. Runout should be verified at installation: use a dial indicator at the center of the tube with the shaft supported on its U-joints. Maximum allowable TIR is 0.010" for passenger and light truck applications. Any damage to the tube that causes runout exceeding this limit requires replacement.

Installation Guidance

  • Install center support bearing before raising shaft into position
  • Align spline pilot into transmission or transfer case output bore
  • Mate rear U-joint cross into the rear yoke with snap rings fully seated
  • Torque center support bearing bracket fasteners to specification
  • Check driveshaft angle: improper center bearing height causes vibration

Ordering

Universal Driveshafts stocks stub midship shafts across a wide range of spline and tube configurations. The 1253-261 ships assembled and ready to install. Pair with a matching center support bearing from our catalog for a complete two-piece driveshaft solution.

Related Stub & Midship Shaft

See the full table

1253-261 questions

What spline count does 1253-261 have?

1253-261 is cut for 26 x 1.115 splines (count × major diameter). Count the splines on the output shaft and measure across the major diameter to confirm.

What part numbers does 1253-261 replace?

1253-261 cross-references to 1253-261-01. Interchange data is for reference; compare the dimensions before substituting.

Is 1253-261 in stock?

Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.