Part No. 1253-261 (also written 1253/261) Stub Midship Shaft, 26 x 1.115 Splines, Butt Dia 2.375", Tube Dia Wall 2.500X0.065
In stock1 ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 1253-261 · Stub Shaft
- Part number
- 1253-261
- Part type
- Stub Shaft
- Condition
- New
- Style
- FIXED
- Tube wall
- 0.065"
- Tube diameter
- 2.500
- Butt diameter
- 2.375
- End to weld
- 3.125
- Splines count diameter
- 26 x 1.115
- Splines length
- 1.120
- Weight
- 2.04 lb
Fitment
USE WITH: 1204-261 , Uses 858018 nut
Interchange / cross-reference
- 1253-261-01
1253-261 replaces or interchanges with 1253-261-01. Cross-reference numbers are supplied for identification; compare the series, spline and bolt-pattern dimensions above before substituting.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 1253-261
The 1253-261 stub midship shaft bridges the gap between transmission output and rear driveshaft section in two-piece driveshaft assemblies. Featuring 26 x 1.115 splines, a 2.375" butt diameter, and a 2.500" x 0.065" wall tube, it is precision-welded to maintain driveline balance within tight tolerances.
Two-Piece Driveshaft Architecture
Long-wheelbase trucks and SUVs use a two-piece driveshaft to avoid resonance frequencies that would be unavoidable with a single long tube. The front section -- the stub midship -- rides on a center support bearing and connects to the front of the rear driveshaft section. The 1253-261 fills this role, providing a dimensionally stable, balanced midship tube ready for installation with a matching center support bearing.
Dimensional Specifications
| Parameter | Value |
|---|---|
| Part Number | 1253-261 |
| Splines Count x Dia. | 26 x 1.115" |
| Spline Length | 1.120" (approx.) |
| Butt Diameter | 2.375" |
| Tube Diameter | 2.500" |
| Tube Wall | 0.065" |
| End-to-Weld Dimension | 3.125" |
Balance and Runout Standards
Midship shafts are finish-balanced after assembly. Runout should be verified at installation: use a dial indicator at the center of the tube with the shaft supported on its U-joints. Maximum allowable TIR is 0.010" for passenger and light truck applications. Any damage to the tube that causes runout exceeding this limit requires replacement.
Installation Guidance
- Install center support bearing before raising shaft into position
- Align spline pilot into transmission or transfer case output bore
- Mate rear U-joint cross into the rear yoke with snap rings fully seated
- Torque center support bearing bracket fasteners to specification
- Check driveshaft angle: improper center bearing height causes vibration
Ordering
Universal Driveshafts stocks stub midship shafts across a wide range of spline and tube configurations. The 1253-261 ships assembled and ready to install. Pair with a matching center support bearing from our catalog for a complete two-piece driveshaft solution.
Related Stub & Midship Shaft
See the full table
1253-242
1253-242
$59.95In stock
1340-20
Stub Midship Shaft, 20 X 1.310 Splines, Butt Dia 2.435", End To Weld 7...
$59.82In stock
1340-20L
Stub Midship Shaft, 20 X 1.310 Splines, Butt Dia 2.435", Tube Dia Wall...
$109.16In stock
1340-21
Stub Midship Shaft, 20 X 1.310 Splines, Butt Dia 2.435", Tube Dia Wall...
$73.13In stock
1442-17
Stub & Midship Shaft, 16 X 1.063 Splines, Butt Dia 1.625", Tube Dia Wa...
$84.04In stock
1442-20
Stub & Midship Shaft, 16 X 1.063 Splines, Butt Dia 1.875", Tube Dia 2....
$48.54In stock
1442-202
Stub Midship Shaft, 20 X 0.853 Splines, Butt Dia 1.875", Tube Dia Wall...
$58.69In stock
1442-209
Stub Midship Shaft, 16 X 1.063 Splines, Butt Dia 1.812", Tube Dia 2.00...
$48.50In stock
1253-261 questions
What spline count does 1253-261 have?
1253-261 is cut for 26 x 1.115 splines (count × major diameter). Count the splines on the output shaft and measure across the major diameter to confirm.
What part numbers does 1253-261 replace?
1253-261 cross-references to 1253-261-01. Interchange data is for reference; compare the dimensions before substituting.
Is 1253-261 in stock?
Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.