N.º de parte 1253-242 (también escrito 1253/242) 1253-242
En stock
La mayoría de las piezas en stock salen el mismo día si se piden antes de las 2pm EST; los tiempos de procesamiento pueden variar.
- Envío gratis en pedidos de piezas de más de $1,000
- Devoluciones en 14 días
- Ayuda con la compatibilidad: (813) 524-6491
Especificaciones 1253-242 · Stub Shaft
- Número de pieza
- 1253-242
- Tipo de pieza
- Stub Shaft
- Condición
- Nuevo
- Estilo
- FIXED
- Diámetro de tubo
- 2.000
- Pared de tubo
- 0.065"
- Diámetro de asiento
- 1.875
- Extremo a soldadura
- 2.875
- Cantidad y diám. de estrías
- 24 x 0.995
- Largo
- 1.180
- Diám. de rodamiento
- 0.985
- Peso
- 1.58 lb
Compatibilidad
use is with : 1204-241 nut sold sepratly: 858018
Calcula el envío a tu código postal
Calcular envío
Tarifas UPS en vivo desde nuestro taller en Florida. Los pedidos de piezas de más de $1,000 tienen envío gratis; el tubo y los cardanes completos siempre se envían con la tarifa UPS.
Retiro en tienda en Florida: gratis
Acerca de 1253-242
The 1253-242 stub shaft or midship shaft is a critical intermediate driveline component used in multi-piece shaft assemblies. With a 1.875-inch butt diameter and 24 x 0.995 spline engagement, it connects the front and rear shaft sections while carrying the center support bearing journal that holds the midshaft in alignment with the vehicle's chassis tunnel.
Dimensional Specifications
| Parameter | Value |
|---|---|
| Style | FIXED |
| Butt Diameter | 1.875" |
| Splines Count x Dia | 24 x 0.995 |
| End to Weld | 2.875" |
| Tube Diameter | 2.000" |
| Tube Wall | 0.065" |
| Bearing Diameter | 0.985" |
| Length | 1.180" |
| Notes | use is with : 1204-241 nut sold sepratly: 858018 |
| Part Number | 1253-242 |
Multi-Piece Driveshaft Architecture
Long-wheelbase trucks and commercial vehicles use two-piece or three-piece driveshafts to avoid the critical whirl speed problem that occurs when a single long shaft is rotated at high RPM. The stub or midship shaft is the intermediate member of this assembly, supported at its midpoint by the center carrier bearing and connected to the rear shaft section at its output end. The bearing journal diameter -- 0.985 inches on the 1253-242 -- must match the carrier bearing's bore for correct fit and concentricity.
Installation and Alignment
- The center support bearing must be shimmed or adjusted so the stub shaft centerline aligns with the front and rear shaft segments -- misalignment of even 1-2mm introduces a permanent operating angle that causes vibration
- Confirm the spline engagement (24 x 0.995) is compatible with the mating nut or coupling specified in the notes: use is with : 1204-241 nut sold sepratly: 858018
- Torque the end nut to specification and verify with a calibrated torque wrench
- After assembly, dynamically balance the complete two-piece assembly on a driveshaft balancer for best NVH results
Specialist Stock at Universal Driveshafts
The 1253-242 midship shaft is a specialized component stocked for direct-replacement applications. Our driveline engineers can cross-reference superseded part numbers and confirm fitment for your specific vehicle and build configuration.
Stub & Midship Shaft relacionados
Ver la tabla completa
1253-261
Eje intermedio (stub), 26 x 1.115 estrías, Diám. de asiento 2.375", Di...
$59.95En stock
1340-20
Eje intermedio (stub), 20 X 1.310 estrías, Diám. de asiento 2.435", Ex...
$59.82En stock
1340-20L
Eje intermedio (stub), 20 X 1.310 estrías, Diám. de asiento 2.435", Di...
$109.16En stock
1340-21
Eje intermedio (stub), 20 X 1.310 estrías, Diám. de asiento 2.435", Di...
$73.13En stock
1442-17
Stub & Midship Shaft, 16 X 1.063 estrías, Diám. de asiento 1.625", Diá...
$84.04En stock
1442-20
Stub & Midship Shaft, 16 X 1.063 estrías, Diám. de asiento 1.875", Diá...
$48.54En stock
1442-202
Eje intermedio (stub), 20 X 0.853 estrías, Diám. de asiento 1.875", Di...
$58.69En stock
1442-209
Eje intermedio (stub), 16 X 1.063 estrías, Diám. de asiento 1.812", Di...
$48.50En stock
1253-242 preguntas
¿Cuántas estrías tiene 1253-242?
1253-242 está cortado para estrías 24 x 0.995 (cantidad × diámetro mayor). Cuenta las estrías del eje de salida y mide el diámetro mayor para confirmar.