3504-291 1350 Series End Yoke

Part No. 3504-291 (also written 3504/291) End Yoke, 1.276" Splines Dia, 1.710" Hub Dia, 1350 Series"

$94.45

In stock1 ready to ship

Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.

  • Free shipping on parts orders over $1,000
  • 14-day returns
  • Fitment help: (813) 524-6491

Specifications 3504-291 · 1350 Series End Yoke

How to measurePoint at a letter to read its measurement
ABCFGED
Part number
3504-291
Part type
End Yoke
Condition
New
Series
1350
Style
BS
Splines count
29
Splines diameter
1.276
Through hole
1.500"
Hub diameter
1.710"
CJ to end
3.188
Bore type
splined
Weight
2.4 lb

Fitment

NUT: 16-74-101, STRAP: 3-70-28, STUB: 3153-291

1350 series parts use 1.188" u-joint bearing caps on a 3.625" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.

Estimate shipping to your ZIP

Estimate shipping

Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.

Local pickup in Florida — free

About 3504-291

When comparing aftermarket end yokes, what matters is dimensional precision and material consistency -- not packaging or price point. The 3504-291 from UDS is built to the 1350 Series OEM specification: 1.276" spline bore, 1.710" hub diameter, and BS snap ring retention. These numbers are non-negotiable -- they either match your output shaft or they don't.

OEM vs. Aftermarket: What Changes

OEM end yokes are manufactured to tight tolerances with controlled heat treatment for the specific vehicle model. The UDS 3504-291 replicates these tolerances in an aftermarket context, using the same 1350 Series dimensional standard that OEM suppliers use. The practical difference is availability: this part ships from Universal Driveshafts' inventory, while OEM sources may require dealer ordering with extended lead times.

  • Spline interface: 1.276" x 29 splines -- matches OEM output shaft
  • Snap ring type: BS -- same retention method as factory
  • Hub diameter: 1.710" -- registers against factory seal bore
  • Note: NUT: 16-74-101
Specification Value
Series 1350 Series
Spline Diameter 1.276"
Spline Count 29
Hub Diameter 1.710"
Center U-Joint to End 3.188"
Through Hole Diameter 1.500"
Snap Ring Style BS
Application Note NUT: 16-74-101
Brand UDS

Specification Table

Full dimensional data for the 3504-291. Every measurement is an as-machined figure, not a nominal or nominal +/- value.

Selecting the Correct Part

The most common ordering error for end yokes is confusing similar-sounding series numbers or assuming that all yokes for a given vehicle are interchangeable. Verify these specifics before ordering the 3504-291: output shaft spline diameter must be 1.276", spline count must be 29, and the shaft's snap ring groove must match the BS style. Through bore clearance (1.500") is especially important if your application routes a cable or shaft through the output yoke bore.

Part 3504-291 is a UDS product. Universal Driveshafts stocks a complete range of 1350 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.

New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.

Related End Yokes in the 1350 series

See the full table

3504-291 questions

What series is 3504-291?

3504-291 is a 1350 series end yoke. Nominal 1350 dimensions are 1.188" bearing caps on a 3.625" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.

What spline count does 3504-291 have?

3504-291 has 29 splines on a 1.276" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.

Is 3504-291 in stock?

Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.