Part No. 3504-10 (also written 3504/10) End Yoke, 1350 Series, 1.188" Splines Dia, 1.875" Hub Dia"
In stock1 ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3504-10 · 1350 Series End Yoke
- Part number
- 3504-10
- Part type
- End Yoke
- Condition
- New
- Series
- 1350
- Style
- BS
- Hub diameter
- 1.875
- CJ to end
- 3.125
- Splines diameter
- 1.188
- Splines count
- 10
- Through hole
- 1.656
- Bore type
- splined
- Weight
- 2.46 lb
Fitment
STRAP PART NUMBER: 3-70-28, CHRYSLER 8.75
1350 series parts use 1.188" u-joint bearing caps on a 3.625" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Interchange / cross-reference
- 3-4-2051-1
3504-10 replaces or interchanges with 3-4-2051-1. Cross-reference numbers are supplied for identification; compare the series, spline and bolt-pattern dimensions above before substituting.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 3504-10
Not all end yokes are created equal -- the material and machining process determine whether a yoke lasts 200,000 miles or fails in 20,000. The 3504-10 is a UDS 1350 Series end yoke manufactured from high-grade steel with machined spline bores, precision bearing seats, and controlled snap ring grooves. It is the correct choice for any drivetrain that demands durability over the long haul.
Material and Construction
The raw material for this yoke is selected for its combination of tensile strength and machinability. After rough forming, the spline bore, hub, and bearing seats are finish-machined on CNC equipment to hold tolerances that exceed OEM specifications. The BS snap ring groove is cut to a consistent depth and width, ensuring that the snap ring seats fully and cannot back out under vibration.
- High-grade steel construction -- resists deformation under high-torque loads
- CNC-machined bearing bores -- consistent, round seats for U-joint caps
- Controlled spline form -- 1.188" diameter, 10-spline interface
- Protective coating -- resists corrosion during storage and service life
| Specification | Value |
|---|---|
| Series | 1350 Series |
| Spline Diameter | 1.188" |
| Spline Count | 10 |
| Hub Diameter | 1.875" |
| Center U-Joint to End | 3.125" |
| Through Hole Diameter | 1.656" |
| Snap Ring Style | BS |
| Application Note | CHRYSLER 8.75 |
| Brand | UDS |
Dimensional Reference
Every dimension on this yoke has a functional purpose. The 1.875" hub diameter determines how the yoke registers against the output shaft seal or retainer. The 3.125" center-to-end measurement affects driveshaft operating length. The 1.656" through hole prevents interference with internal shafts or speedometer cables. None of these dimensions can be ignored when selecting a replacement.
Application and Installation
This yoke is designed for CHRYSLER 8.75. Installation requires a clean output shaft free of nicks, corrosion, or damaged splines. Inspect the snap ring groove in the shaft before installing the new yoke. Torque the retaining hardware to specification -- do not rely on thread friction alone to retain the yoke under high-RPM operation.
Pair with a fresh 1350 Series U-joint for a complete driveline service. Reusing an old U-joint with a new yoke negates the benefits of the replacement.
Part 3504-10 is a UDS product. Universal Driveshafts stocks a complete range of 1350 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Related End Yokes in the 1350 series
See the full table
3504-04
End Yoke, 1.312" Splines Dia, 2.110" Hub Dia, 30 Spline
$114.87In stock
3504-09
End Yoke, 1350 Series, 1.343" Splines Dia, 1.812" Hub Dia
$121.02In stock
N3-4-JK08
End Yoke, 1350 Series, 1.250" Splines Dia, 1.85" Hub Dia
$111.55In stock
3504-03
End Yoke, 1350 Series, 1.343" Splines Dia, 1.812" Hub Dia
$102.26In stock
3504-101
End Yoke, 1350 Series, 1.375" Splines Dia, 1.750" Hub Dia
$118.59In stock
3504-85
End Yoke, 1350 Series, 1.312" Splines Dia, 1.94" Hub Dia
$108.75In stock
3504-243
End Yoke, 1350 Series, 1.250" Splines Dia, 1.876" Hub Dia
$107.73In stock
3504-06
End Yoke, 1350 Series, 1.146" Splines Dia, 1.552" Hub Dia
$92.40In stock
3504-10 questions
What series is 3504-10?
3504-10 is a 1350 series end yoke. Nominal 1350 dimensions are 1.188" bearing caps on a 3.625" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 3504-10 have?
3504-10 has 10 splines on a 1.188" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.
What part numbers does 3504-10 replace?
3504-10 cross-references to 3-4-2051-1. Interchange data is for reference; compare the dimensions before substituting.
Is 3504-10 in stock?
Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.