Part No. 3504-291 (also written 3504/291) End Yoke, 1.276" Splines Dia, 1.710" Hub Dia, 1350 Series"
In stock1 ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3504-291 · 1350 Series End Yoke
- Part number
- 3504-291
- Part type
- End Yoke
- Condition
- New
- Series
- 1350
- Style
- BS
- Splines count
- 29
- Splines diameter
- 1.276
- Through hole
- 1.500"
- Hub diameter
- 1.710"
- CJ to end
- 3.188
- Bore type
- splined
- Weight
- 2.4 lb
Fitment
NUT: 16-74-101, STRAP: 3-70-28, STUB: 3153-291
1350 series parts use 1.188" u-joint bearing caps on a 3.625" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 3504-291
When comparing aftermarket end yokes, what matters is dimensional precision and material consistency -- not packaging or price point. The 3504-291 from UDS is built to the 1350 Series OEM specification: 1.276" spline bore, 1.710" hub diameter, and BS snap ring retention. These numbers are non-negotiable -- they either match your output shaft or they don't.
OEM vs. Aftermarket: What Changes
OEM end yokes are manufactured to tight tolerances with controlled heat treatment for the specific vehicle model. The UDS 3504-291 replicates these tolerances in an aftermarket context, using the same 1350 Series dimensional standard that OEM suppliers use. The practical difference is availability: this part ships from Universal Driveshafts' inventory, while OEM sources may require dealer ordering with extended lead times.
- Spline interface: 1.276" x 29 splines -- matches OEM output shaft
- Snap ring type: BS -- same retention method as factory
- Hub diameter: 1.710" -- registers against factory seal bore
- Note: NUT: 16-74-101
| Specification | Value |
|---|---|
| Series | 1350 Series |
| Spline Diameter | 1.276" |
| Spline Count | 29 |
| Hub Diameter | 1.710" |
| Center U-Joint to End | 3.188" |
| Through Hole Diameter | 1.500" |
| Snap Ring Style | BS |
| Application Note | NUT: 16-74-101 |
| Brand | UDS |
Specification Table
Full dimensional data for the 3504-291. Every measurement is an as-machined figure, not a nominal or nominal +/- value.
Selecting the Correct Part
The most common ordering error for end yokes is confusing similar-sounding series numbers or assuming that all yokes for a given vehicle are interchangeable. Verify these specifics before ordering the 3504-291: output shaft spline diameter must be 1.276", spline count must be 29, and the shaft's snap ring groove must match the BS style. Through bore clearance (1.500") is especially important if your application routes a cable or shaft through the output yoke bore.
Part 3504-291 is a UDS product. Universal Driveshafts stocks a complete range of 1350 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Related End Yokes in the 1350 series
See the full table
3504-04
End Yoke, 1.312" Splines Dia, 2.110" Hub Dia, 30 Spline
$114.87In stock
3504-09
End Yoke, 1350 Series, 1.343" Splines Dia, 1.812" Hub Dia
$121.02In stock
N3-4-JK08
End Yoke, 1350 Series, 1.250" Splines Dia, 1.85" Hub Dia
$111.55In stock
3504-03
End Yoke, 1350 Series, 1.343" Splines Dia, 1.812" Hub Dia
$102.26In stock
3504-101
End Yoke, 1350 Series, 1.375" Splines Dia, 1.750" Hub Dia
$118.59In stock
3504-85
End Yoke, 1350 Series, 1.312" Splines Dia, 1.94" Hub Dia
$108.75In stock
3504-10
End Yoke, 1350 Series, 1.188" Splines Dia, 1.875" Hub Dia"
$121.07In stock
3504-243
End Yoke, 1350 Series, 1.250" Splines Dia, 1.876" Hub Dia
$107.73In stock
3504-291 questions
What series is 3504-291?
3504-291 is a 1350 series end yoke. Nominal 1350 dimensions are 1.188" bearing caps on a 3.625" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 3504-291 have?
3504-291 has 29 splines on a 1.276" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.
Is 3504-291 in stock?
Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.