3104-301 1310 Series End Yoke

部品番号 3104-301 (別表記 3104/301) エンドヨーク, スプライン径 1.328", ハブ径 1.739", 30 スプライン

$94.52

在庫あり

在庫品の多くは 2pm(EST)までのご注文で当日発送いたします。処理時間は前後する場合があります。

  • 部品注文の送料無料金額 $1,000
  • 14日以内返品可能
  • 適合に関するサポート: (813) 524-6491

仕様 3104-301 · 1310 Series End Yoke

計測方法文字にカーソルを合わせると、その寸法が表示されます
ABCFGED
部品番号
3104-301
パーツタイプ
エンドヨーク
状態
新品
シリーズ
1310
スタイル
UB
スプライン数
30
ハブ径
1.739
スプライン径
1.328
通し穴
1.181
ユニバーサルジョイントから端部まで
2.598
ボアタイプ
splined
重量
2 lb

適合性

U BOLT PART NUMBER: 2-94-28, GM8.5 VETTE

1310 シリーズのパーツには 1.062" ユニバーサルジョイントのベアリングキャップを使用します スナップリング間幅 3.219" (公称)。ご注文前に、相手側のヨークまたはジョイントのキャップ径をご確認ください。

郵便番号への送料を見積もる

送料を計算

フロリダの弊社ショップからのリアルタイム UPS 送料。パーツのご注文が $1,000 送料無料 — チューブおよび完全なプロペラシャフトは常にUPSの料金で発送されます。

フロリダでの店頭受取 — 無料

3104-301 について

Replacing an end yoke is a straightforward job when you have the right part. The 3104-301 -- a UDS 1310 Series end yoke -- is dimensioned to drop onto the output shaft splines without modification, provided your shaft matches the 1.328" spline diameter and 30-spline count. This guide covers what to check before you order and what to do during installation.

Pre-Order Verification

Before removing your old yoke, record the following from either the old part or the output shaft:

  • Spline diameter: Should match 1.328" for this part
  • Spline count: Should match 30
  • Snap ring style: UB -- check whether the groove is on the inside or outside of the bearing bore
  • Series: 1310 Series -- look for the series stamp on the U-joint caps or the original yoke

Application note: GM8.5 VETTE

Specification Value
Series 1310 Series
Spline Diameter 1.328"
Spline Count 30
Hub Diameter 1.739"
Center U-Joint to End 2.598"
Through Hole Diameter 1.181"
Snap Ring Style UB
Application Note GM8.5 VETTE
Brand UDS

Dimensional Specifications

The 3104-301 carries the following dimensions, which define its fit envelope. Verify each against your application before ordering.

Installation Steps

Once you have confirmed fitment, installation proceeds as follows:

  1. Remove the old yoke by unthreading the retaining nut and sliding the yoke off the output shaft splines. Mark the driveshaft-to-yoke orientation before disassembly to maintain balance phasing.
  2. Clean the output shaft splines with a wire brush and solvent. Inspect for cracks or worn spline flanks.
  3. Apply a thin coat of assembly lubricant to the shaft splines. Do not over-lubricate -- excess grease can cause seal contamination.
  4. Slide the 3104-301 onto the splines, aligning your reference marks. The hub diameter of 1.739" should register smoothly against the seal bore.
  5. Install a new snap ring (UB style) in the groove. Confirm it seats fully around the perimeter.
  6. Torque the retaining nut to the vehicle manufacturer's specification.

After installation, lower the vehicle and drive briefly before inspecting for leaks or vibration. Any vibration at highway speed indicates a balance issue -- have the driveshaft rebalanced with the new yoke installed.

Part 3104-301 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.

New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.

1310 シリーズの関連する エンドヨーク

全一覧表を見る

3104-301 ご質問

3104-301 はどのシリーズですか?

3104-301 は 1310 シリーズの エンドヨーク です。 1310 シリーズの公称寸法は 1.062" ベアリングキャップです スナップリング間幅 3.219"。ご注文前に、古いジョイントのキャップ径を測ってシリーズをご確認ください。

3104-301 のスプライン数はいくつですか?

3104-301 はスプライン径 1.328" に 30 スプラインを備えています。 出力シャフトのスプライン数を数え、外径(最大径)を測って確認してください。

この翻訳はAIによって作成されたものであり、エラーが含まれている可能性があります。ご不明な点がございましたら、(813) 524-6491にお電話いただくか、英語に切り替えてください。