N.º de parte 3104-301 (también escrito 3104/301) Yugo de extremo, Diám. de estrías 1.328", Diám. de cubo 1.739", 30 estrías
En stock
La mayoría de las piezas en stock salen el mismo día si se piden antes de las 2pm EST; los tiempos de procesamiento pueden variar.
- Envío gratis en pedidos de piezas de más de $1,000
- Devoluciones en 14 días
- Ayuda con la compatibilidad: (813) 524-6491
Especificaciones 3104-301 · 1310 Series End Yoke
- Número de pieza
- 3104-301
- Tipo de pieza
- Yugo de extremo
- Condición
- Nuevo
- Serie
- 1310
- Estilo
- UB
- Cantidad de estrías
- 30
- Diám. de cubo
- 1.739
- Diám. de estrías
- 1.328
- Agujero pasante
- 1.181
- Cruceta a extremo
- 2.598
- Tipo de orificio
- splined
- Peso
- 2 lb
Compatibilidad
U BOLT PART NUMBER: 2-94-28, GM8.5 VETTE
Las piezas de serie 1310 usan copas de rodamiento de cruceta de 1.062" con un ancho de 3.219" de anillo a anillo (nominal). Confirma el diámetro de copa en el yugo o la cruceta que acopla antes de comprar.
Calcula el envío a tu código postal
Calcular envío
Tarifas UPS en vivo desde nuestro taller en Florida. Los pedidos de piezas de más de $1,000 tienen envío gratis; el tubo y los cardanes completos siempre se envían con la tarifa UPS.
Retiro en tienda en Florida: gratis
Acerca de 3104-301
Replacing an end yoke is a straightforward job when you have the right part. The 3104-301 -- a UDS 1310 Series end yoke -- is dimensioned to drop onto the output shaft splines without modification, provided your shaft matches the 1.328" spline diameter and 30-spline count. This guide covers what to check before you order and what to do during installation.
Pre-Order Verification
Before removing your old yoke, record the following from either the old part or the output shaft:
- Spline diameter: Should match 1.328" for this part
- Spline count: Should match 30
- Snap ring style: UB -- check whether the groove is on the inside or outside of the bearing bore
- Series: 1310 Series -- look for the series stamp on the U-joint caps or the original yoke
Application note: GM8.5 VETTE
| Specification | Value |
|---|---|
| Series | 1310 Series |
| Spline Diameter | 1.328" |
| Spline Count | 30 |
| Hub Diameter | 1.739" |
| Center U-Joint to End | 2.598" |
| Through Hole Diameter | 1.181" |
| Snap Ring Style | UB |
| Application Note | GM8.5 VETTE |
| Brand | UDS |
Dimensional Specifications
The 3104-301 carries the following dimensions, which define its fit envelope. Verify each against your application before ordering.
Installation Steps
Once you have confirmed fitment, installation proceeds as follows:
- Remove the old yoke by unthreading the retaining nut and sliding the yoke off the output shaft splines. Mark the driveshaft-to-yoke orientation before disassembly to maintain balance phasing.
- Clean the output shaft splines with a wire brush and solvent. Inspect for cracks or worn spline flanks.
- Apply a thin coat of assembly lubricant to the shaft splines. Do not over-lubricate -- excess grease can cause seal contamination.
- Slide the 3104-301 onto the splines, aligning your reference marks. The hub diameter of 1.739" should register smoothly against the seal bore.
- Install a new snap ring (UB style) in the groove. Confirm it seats fully around the perimeter.
- Torque the retaining nut to the vehicle manufacturer's specification.
After installation, lower the vehicle and drive briefly before inspecting for leaks or vibration. Any vibration at highway speed indicates a balance issue -- have the driveshaft rebalanced with the new yoke installed.
Part 3104-301 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Yugos de extremo relacionados de la serie 1310
Ver la tabla completa
3104-26CV
Yugo de extremo, serie 1310, 26 estrías, Estilo CV
$48.27En stock
3104-05
Yugo de extremo, Diám. de estrías 1.188", serie 1310, Diám. de cubo 1....
$84.60En stock
3104-231
Yugo de extremo, Diám. de estrías 1.26", Diám. de cubo 1.562", 23 estr...
$104.94En stock
3104-02
Yugo de extremo, Diám. de estrías 1.146", Diám. de cubo 1.844", 26 est...
$99.17En stock
2-4-0523
Yugo de extremo, serie 1310, Diám. de cubo 2.125", 2.562" Junta a extr...
$43.88En stock
2-4-1233
Yugo de extremo - agujero redondo serie 1310, 1.500 Agujero Chavetero:...
$18.91En stock
N2-4-JK06
Yugo de extremo, Diám. de estrías 1.25", Diám. de cubo 1.85", 24 estrí...
$115.63En stock
3104-321CV
Yugo de extremo CV Conversion To 1310 Jeep JK NP241 07-18, counterbore...
$42.66En stock
3104-301 preguntas
¿De qué serie es 3104-301?
3104-301 pertenece a la serie 1310 (Yugo de extremo). Las dimensiones nominales de la serie 1310 son copas de 1.062" con un ancho de 3.219" de anillo a anillo. Mide el diámetro de copa de tu cruceta vieja para confirmar la serie antes de comprar.
¿Cuántas estrías tiene 3104-301?
3104-301 tiene 30 estrías en un diámetro de estrías de 1.328". Cuenta las estrías del eje de salida y mide el diámetro mayor para confirmar.