3104-301 1310 Series End Yoke

N° de pièce 3104-301 (aussi écrit 3104/301) Fourchette d'extrémité, Diam. cannelures 1.328", Diam. moyeu 1.739", 30 cannelures

$94.52

En stock

La plupart des pièces en stock sont expédiées le jour même pour toute commande passée avant 2pm EST ; les délais de traitement peuvent varier.

  • Livraison gratuite pour les commandes de pièces supérieures à $1,000
  • Retours sous 14 jours
  • Aide à la compatibilité : (813) 524-6491

Spécifications 3104-301 · 1310 Series End Yoke

Comment mesurerPointez une lettre pour voir sa mesure
ABCFGED
Référence de pièce
3104-301
Type de pièce
Fourchette d'extrémité
État
Nouveau
Série
1310
Style
UB
Nombre de cannelures
30
Diam. de moyeu
1.739
Diam. des cannelures
1.328
Trou traversant
1.181
Croisillon à l'extrémité
2.598
Type d'alésage
splined
Poids
2 lb

Compatibilité

U BOLT PART NUMBER: 2-94-28, GM8.5 VETTE

Les pièces de la série 1310 utilisent des bonnets de roulement de croisillon de 1.062" avec une largeur circlips à circlips de 3.219" (nominal). Confirmez le diamètre des bols sur la fourche ou le croisillon couplé avant de commander.

Estimez les frais de livraison pour votre code postal

Estimer les frais de port

Tarifs UPS en direct depuis notre atelier en Floride. Commandes de pièces supérieures à $1,000 livraison gratuite — le tube et les arbres de transmission complets sont toujours expédiés au tarif UPS.

Retrait en magasin en Floride — gratuit

À propos de 3104-301

Replacing an end yoke is a straightforward job when you have the right part. The 3104-301 -- a UDS 1310 Series end yoke -- is dimensioned to drop onto the output shaft splines without modification, provided your shaft matches the 1.328" spline diameter and 30-spline count. This guide covers what to check before you order and what to do during installation.

Pre-Order Verification

Before removing your old yoke, record the following from either the old part or the output shaft:

  • Spline diameter: Should match 1.328" for this part
  • Spline count: Should match 30
  • Snap ring style: UB -- check whether the groove is on the inside or outside of the bearing bore
  • Series: 1310 Series -- look for the series stamp on the U-joint caps or the original yoke

Application note: GM8.5 VETTE

Specification Value
Series 1310 Series
Spline Diameter 1.328"
Spline Count 30
Hub Diameter 1.739"
Center U-Joint to End 2.598"
Through Hole Diameter 1.181"
Snap Ring Style UB
Application Note GM8.5 VETTE
Brand UDS

Dimensional Specifications

The 3104-301 carries the following dimensions, which define its fit envelope. Verify each against your application before ordering.

Installation Steps

Once you have confirmed fitment, installation proceeds as follows:

  1. Remove the old yoke by unthreading the retaining nut and sliding the yoke off the output shaft splines. Mark the driveshaft-to-yoke orientation before disassembly to maintain balance phasing.
  2. Clean the output shaft splines with a wire brush and solvent. Inspect for cracks or worn spline flanks.
  3. Apply a thin coat of assembly lubricant to the shaft splines. Do not over-lubricate -- excess grease can cause seal contamination.
  4. Slide the 3104-301 onto the splines, aligning your reference marks. The hub diameter of 1.739" should register smoothly against the seal bore.
  5. Install a new snap ring (UB style) in the groove. Confirm it seats fully around the perimeter.
  6. Torque the retaining nut to the vehicle manufacturer's specification.

After installation, lower the vehicle and drive briefly before inspecting for leaks or vibration. Any vibration at highway speed indicates a balance issue -- have the driveshaft rebalanced with the new yoke installed.

Part 3104-301 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.

New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.

Fourchettes d'extrémité associés de la série 1310

Voir le tableau complet

3104-301 questions

De quelle série est 3104-301 ?

3104-301 est un élément de la série 1310 Fourchette d'extrémité. Les dimensions nominales de la série 1310 sont des bols de roulement de 1.062" avec une largeur circlips à circlips de 3.219". Mesurez le diamètre des bols de votre ancien croisillon pour confirmer la série avant de commander.

Combien de cannelures possède 3104-301 ?

3104-301 comporte 30 cannelures sur un diamètre de cannelure de 1.328". Comptez les cannelures sur l'arbre de sortie et mesurez le diamètre extérieur pour confirmer.

Cette traduction a été réalisée par IA et peut contenir des erreurs. En cas de doute, appelez le (813) 524-6491 ou passez en anglais.