1340-20L Stub Shaft
Slip

N.º de parte 1340-20L (también escrito 1340/20L) Eje intermedio (stub), 20 X 1.310 estrías, Diám. de asiento 2.435", Diám. × pared de tubo 2.560x0.065

$109.16

En stock1 listos para enviar

La mayoría de las piezas en stock salen el mismo día si se piden antes de las 2pm EST; los tiempos de procesamiento pueden variar.

  • Envío gratis en pedidos de piezas de más de $1,000
  • Devoluciones en 14 días
  • Ayuda con la compatibilidad: (813) 524-6491

Especificaciones 1340-20L · Stub Shaft

Cómo medirSeñala una letra para ver su medida
EBADFC
Número de pieza
1340-20L
Tipo de pieza
Stub Shaft
Condición
Nuevo
Estilo
Slip
Pared de tubo
0.065"
Diámetro de asiento
2.435
Cantidad y diám. de estrías
20 X 1.310
Extremo a soldadura
9.375
Largo de estrías
6.500
Diámetro de tubo
2.560
Peso
5 lb

Compatibilidad

Toyota, Sold only in kit 1343-20L

Calcula el envío a tu código postal

Calcular envío

Tarifas UPS en vivo desde nuestro taller en Florida. Los pedidos de piezas de más de $1,000 tienen envío gratis; el tubo y los cardanes completos siempre se envían con la tarifa UPS.

Retiro en tienda en Florida: gratis

Acerca de 1340-20L

The 1340-20L stub midship shaft bridges the gap between transmission output and rear driveshaft section in two-piece driveshaft assemblies. Featuring 20 X 1.310 splines, a 2.435" butt diameter, and a 2.560" x 0.065" wall tube, it is precision-welded to maintain driveline balance within tight tolerances.

Two-Piece Driveshaft Architecture

Long-wheelbase trucks and SUVs use a two-piece driveshaft to avoid resonance frequencies that would be unavoidable with a single long tube. The front section -- the stub midship -- rides on a center support bearing and connects to the front of the rear driveshaft section. The 1340-20L fills this role, providing a dimensionally stable, balanced midship tube ready for installation with a matching center support bearing.

Dimensional Specifications

ParameterValue
Part Number1340-20L
Splines Count x Dia.20 X 1.310"
Spline Length6.500" (approx.)
Butt Diameter2.435"
Tube Diameter2.560"
Tube Wall0.065"
End-to-Weld Dimension9.375"

Balance and Runout Standards

Midship shafts are finish-balanced after assembly. Runout should be verified at installation: use a dial indicator at the center of the tube with the shaft supported on its U-joints. Maximum allowable TIR is 0.010" for passenger and light truck applications. Any damage to the tube that causes runout exceeding this limit requires replacement.

Installation Guidance

  • Install center support bearing before raising shaft into position
  • Align spline pilot into transmission or transfer case output bore
  • Mate rear U-joint cross into the rear yoke with snap rings fully seated
  • Torque center support bearing bracket fasteners to specification
  • Check driveshaft angle: improper center bearing height causes vibration

Ordering

Universal Driveshafts stocks stub midship shafts across a wide range of spline and tube configurations. The 1340-20L ships assembled and ready to install. Pair with a matching center support bearing from our catalog for a complete two-piece driveshaft solution.

Stub & Midship Shaft relacionados

Ver la tabla completa

1340-20L preguntas

¿Cuántas estrías tiene 1340-20L?

1340-20L está cortado para estrías 20 X 1.310 (cantidad × diámetro mayor). Cuenta las estrías del eje de salida y mide el diámetro mayor para confirmar.

¿Hay 1340-20L en existencia?

Sí. Hay 1 en existencia en Florida. La mayoría de los pedidos hechos antes de las 2 p. m. EST en día hábil salen el mismo día.

Esta traducción fue hecha con IA y puede contener errores. Si algo no queda claro, llame al (813) 524-6491 o cambie a inglés.