Part No. 3104-09 (also written 3104/09) End Yoke, 1.328" Splines Dia, 1.739" Hub Dia, 30 Spline
In stock
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3104-09 · 1310 Series End Yoke
- Part number
- 3104-09
- Part type
- End Yoke
- Condition
- New
- Series
- 1310
- Style
- BS
- Splines count
- 30
- Hub diameter
- 1.739
- Splines diameter
- 1.328
- CJ to end
- 2.850"
- Through hole
- 1.170"
- Bore type
- splined
- Weight
- 2.46 lb
Fitment
GM 8.875, STRAP PART NUMBER:1-0024
1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 3104-09
The 1310 Series driveshaft standard has been the backbone of medium-duty automotive and light truck driveline engineering for decades. The 3104-09 end yoke from UDS is manufactured to the same dimensional standards that define this series, ensuring backward and forward compatibility across the wide range of vehicles and equipment that run 1310 Series drivetrain components.
The 1310 Series Standard Explained
Each driveshaft series -- 1100, 1310, 1350, and so on -- is defined by a specific set of U-joint cap dimensions, yoke ear geometry, and torque ratings. The 1310 Series designation tells you the cap diameter, width, and load envelope this yoke is designed for. Mixing series without proper adapter joints creates mismatched geometries that fail under load. The 3104-09 keeps everything within the 1310 Series specification.
- Spline diameter: 1.328" -- the 1310 Series output shaft standard
- Spline count: 30
- Snap ring style: BS -- standard for 1310 Series service
- Hub diameter: 1.739" -- mates with 1310 Series-rated differential or transfer case outputs
| Specification | Value |
|---|---|
| Series | 1310 Series |
| Spline Diameter | 1.328" |
| Spline Count | 30 |
| Hub Diameter | 1.739" |
| Center U-Joint to End | 2.850" |
| Through Hole Diameter | 1.170" |
| Snap Ring Style | BS |
| Application Note | GM 8.875 |
| Brand | UDS |
Part Specifications
Dimensional adherence to the 1310 Series standard means this yoke will mate with any properly dimensioned 1310 Series U-joint and driveshaft. Application: GM 8.875. The following table lists every critical dimension.
Ordering and Fitment Verification
Ordering the correct end yoke requires matching three numbers: the spline diameter (1.328"), the spline count (30), and the snap ring style (BS). If your shaft differs from these values, this part will not fit -- consult our fitment guide or contact our technical team before ordering.
The through hole diameter of 1.170" is relevant for applications with internal shafts or speedometer cable routing through the output yoke. The center-U-joint-to-end dimension of 2.850" must be matched to your driveshaft slip yoke or tube assembly for correct operating length.
Part 3104-09 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Related End Yokes in the 1310 series
See the full table
3104-26CV
End Yoke, 1310 Series, 26 Splines, Style CV
$48.27In stock
3104-05
End Yoke, 1.188" Splines Dia, 1310 Series, 1.521" Hub Dia
$84.60In stock
3104-231
End Yoke, 1.26" Splines Dia, 1.562" Hub Dia, 23 Spline
$104.94In stock
3104-02
End Yoke, 1.146" Splines Dia, 1.844" Hub Dia, 26 Spline
$99.17In stock
2-4-0523
End Yoke, 1310 Series, 2.125" Hub Dia, 2.562" Cj To End
$43.88In stock
2-4-1233
End Yoke - Round Bore 1310 Series, 1.500 Bore KEYWAY: 0.375, Hub Diame...
$18.91In stock
N2-4-JK06
End Yoke, 1.25" Splines dia, 1.85" Hub Dia, 24 Spline
$115.63In stock
3104-321CV
End Yoke CV Conversion To 1310 Jeep JK NP241 07-18, counterbore by nut...
$42.66In stock
3104-09 questions
What series is 3104-09?
3104-09 is a 1310 series end yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 3104-09 have?
3104-09 has 30 splines on a 1.328" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.