N.º de parte N3-4-JK08 Yugo de extremo, serie 1350, Diám. de estrías 1.250", Diám. de cubo 1.85"
En stock4 listos para enviar
La mayoría de las piezas en stock salen el mismo día si se piden antes de las 2pm EST; los tiempos de procesamiento pueden variar.
- Envío gratis en pedidos de piezas de más de $1,000
- Devoluciones en 14 días
- Ayuda con la compatibilidad: (813) 524-6491
Especificaciones N3-4-JK08 · 1350 Series End Yoke
- Número de pieza
- N3-4-JK08
- Tipo de pieza
- Yugo de extremo
- Condición
- Nuevo
- Serie
- 1350
- Estilo
- UB
- Agujero pasante
- 1.500"
- Cantidad de estrías
- 24
- Diám. de estrías
- 1.250"
- Tipo de orificio
- splined
- Diám. de cubo
- 1.85
- Cruceta a extremo
- 3.100"
- Peso
- 2.55 lb
Compatibilidad
FITS JEEP WRANGLER JK DANA 30 AND DANA 44 FRONT END
Las piezas de serie 1350 usan copas de rodamiento de cruceta de 1.188" con un ancho de 3.625" de anillo a anillo (nominal). Confirma el diámetro de copa en el yugo o la cruceta que acopla antes de comprar.
Calcula el envío a tu código postal
Calcular envío
Tarifas UPS en vivo desde nuestro taller en Florida. Los pedidos de piezas de más de $1,000 tienen envío gratis; el tubo y los cardanes completos siempre se envían con la tarifa UPS.
Retiro en tienda en Florida: gratis
Acerca de N3-4-JK08
Replacing an end yoke is a straightforward job when you have the right part. The N3-4-JK08 -- a UDS 1350 Series end yoke -- is dimensioned to drop onto the output shaft splines without modification, provided your shaft matches the 1.250" spline diameter and 24-spline count. This guide covers what to check before you order and what to do during installation.
Pre-Order Verification
Before removing your old yoke, record the following from either the old part or the output shaft:
- Spline diameter: Should match 1.250" for this part
- Spline count: Should match 24
- Snap ring style: UB -- check whether the groove is on the inside or outside of the bearing bore
- Series: 1350 Series -- look for the series stamp on the U-joint caps or the original yoke
Application note: FITS JEEP WRANGLER JK DANA 30 AND DANA 44 FRONT END
| Specification | Value |
|---|---|
| Series | 1350 Series |
| Spline Diameter | 1.250" |
| Spline Count | 24 |
| Hub Diameter | 1.85" |
| Center U-Joint to End | 3.100" |
| Through Hole Diameter | 1.500" |
| Snap Ring Style | UB |
| Application Note | FITS JEEP WRANGLER JK DANA 30 AND DANA 44 FRONT END |
| Brand | UDS |
Dimensional Specifications
The N3-4-JK08 carries the following dimensions, which define its fit envelope. Verify each against your application before ordering.
Installation Steps
Once you have confirmed fitment, installation proceeds as follows:
- Remove the old yoke by unthreading the retaining nut and sliding the yoke off the output shaft splines. Mark the driveshaft-to-yoke orientation before disassembly to maintain balance phasing.
- Clean the output shaft splines with a wire brush and solvent. Inspect for cracks or worn spline flanks.
- Apply a thin coat of assembly lubricant to the shaft splines. Do not over-lubricate -- excess grease can cause seal contamination.
- Slide the N3-4-JK08 onto the splines, aligning your reference marks. The hub diameter of 1.85" should register smoothly against the seal bore.
- Install a new snap ring (UB style) in the groove. Confirm it seats fully around the perimeter.
- Torque the retaining nut to the vehicle manufacturer's specification.
After installation, lower the vehicle and drive briefly before inspecting for leaks or vibration. Any vibration at highway speed indicates a balance issue -- have the driveshaft rebalanced with the new yoke installed.
Part N3-4-JK08 is a UDS product. Universal Driveshafts stocks a complete range of 1350 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Yugos de extremo relacionados de la serie 1350
Ver la tabla completa
3504-04
Yugo de extremo, Diám. de estrías 1.312", Diám. de cubo 2.110", 30 est...
$114.87En stock
3504-09
Yugo de extremo, serie 1350, Diám. de estrías 1.343", Diám. de cubo 1....
$121.02En stock
3504-03
Yugo de extremo, serie 1350, Diám. de estrías 1.343", Diám. de cubo 1....
$102.26En stock
3504-101
Yugo de extremo, serie 1350, Diám. de estrías 1.375", Diám. de cubo 1....
$118.59En stock
3504-85
Yugo de extremo, serie 1350, Diám. de estrías 1.312", Diám. de cubo 1....
$108.75En stock
3504-10
Yugo de extremo, serie 1350, Diám. de estrías 1.188", Diám. de cubo 1....
$121.07En stock
3504-243
Yugo de extremo, serie 1350, Diám. de estrías 1.250", Diám. de cubo 1....
$107.73En stock
3504-06
Yugo de extremo, serie 1350, Diám. de estrías 1.146", Diám. de cubo 1....
$92.40En stock
N3-4-JK08 preguntas
¿De qué serie es N3-4-JK08?
N3-4-JK08 pertenece a la serie 1350 (Yugo de extremo). Las dimensiones nominales de la serie 1350 son copas de 1.188" con un ancho de 3.625" de anillo a anillo. Mide el diámetro de copa de tu cruceta vieja para confirmar la serie antes de comprar.
¿Cuántas estrías tiene N3-4-JK08?
N3-4-JK08 tiene 24 estrías en un diámetro de estrías de 1.250". Cuenta las estrías del eje de salida y mide el diámetro mayor para confirmar.
¿Hay N3-4-JK08 en existencia?
Sí. Hay 4 en existencia en Florida. La mayoría de los pedidos hechos antes de las 2 p. m. EST en día hábil salen el mismo día.