零件号 5504-01 (也写作 5504/01) 端叉, 1550系列, 花键直径 1.609", 轮毂直径 2.500"
现货1 件准备发货
大多数现货配件在 2pm EST 前下单可当天发货;处理时间可能有所不同。
- 配件订单满 $ 免运费1,000
- 14天退货
- 适配咨询: (813) 524-6491
规格 5504-01 · 1550 Series End Yoke
- 零件编号
- 5504-01
- 零件类型
- 端叉
- 状态
- 全新
- 系列
- 1550
- 样式
- BS
- 万向节到端部
- 4.406
- 轮毂直径
- 2.500"
- 花键数
- 37
- 花键直径
- 1.609
- 通孔
- 2.000"
- 孔类型
- splined
- 重量
- 5.52 lb
适配性
DANA 80
1550 系列零件使用 1.375" 万向节轴承盖,卡簧到卡簧宽度为 4.875" (标称)。订购前请确认配对万向节叉或万向节上的轴承盖直径。
互换 / 交叉参考
- 4-4-6851-1X
5504-01 可替换或互换自 4-4-6851-1X. 交叉参考编号仅供识别;购买替代件前,请先比对上方的系列、花键和螺栓孔距尺寸。
按您的邮编估算运费
计算运费
从我们在佛罗里达州的仓库提供实时 UPS 运费。配件订单超过 $1,000 免运费 — 传动轴管和完整传动轴始终按 UPS 费率运送。
佛罗里达州本地自提 — 免费
关于 5504-01
Replacing an end yoke is a straightforward job when you have the right part. The 5504-01 -- a UDS 1550 Series end yoke -- is dimensioned to drop onto the output shaft splines without modification, provided your shaft matches the 1.609" spline diameter and 37-spline count. This guide covers what to check before you order and what to do during installation.
Pre-Order Verification
Before removing your old yoke, record the following from either the old part or the output shaft:
- Spline diameter: Should match 1.609" for this part
- Spline count: Should match 37
- Snap ring style: BS -- check whether the groove is on the inside or outside of the bearing bore
- Series: 1550 Series -- look for the series stamp on the U-joint caps or the original yoke
Application note: DANA 80
| Specification | Value |
|---|---|
| Series | 1550 Series |
| Spline Diameter | 1.609" |
| Spline Count | 37 |
| Hub Diameter | 2.500" |
| Center U-Joint to End | 4.406" |
| Through Hole Diameter | 2.000" |
| Snap Ring Style | BS |
| Application Note | DANA 80 |
| Brand | UDS |
Dimensional Specifications
The 5504-01 carries the following dimensions, which define its fit envelope. Verify each against your application before ordering.
Installation Steps
Once you have confirmed fitment, installation proceeds as follows:
- Remove the old yoke by unthreading the retaining nut and sliding the yoke off the output shaft splines. Mark the driveshaft-to-yoke orientation before disassembly to maintain balance phasing.
- Clean the output shaft splines with a wire brush and solvent. Inspect for cracks or worn spline flanks.
- Apply a thin coat of assembly lubricant to the shaft splines. Do not over-lubricate -- excess grease can cause seal contamination.
- Slide the 5504-01 onto the splines, aligning your reference marks. The hub diameter of 2.500" should register smoothly against the seal bore.
- Install a new snap ring (BS style) in the groove. Confirm it seats fully around the perimeter.
- Torque the retaining nut to the vehicle manufacturer's specification.
After installation, lower the vehicle and drive briefly before inspecting for leaks or vibration. Any vibration at highway speed indicates a balance issue -- have the driveshaft rebalanced with the new yoke installed.
Part 5504-01 is a UDS product. Universal Driveshafts stocks a complete range of 1550 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
1550 系列中相关的 端叉
查看完整表格
4-4-1901-1
端叉 - 花键孔 Series1550, Strap 型式, 1.750x10 花键, 2.625 轮毂 diamet...
$85.81现货
4-4-7901-2U
端叉, 1550系列 - 花键; 10x1.5 - UDS
$75.64现货
3104-26CV
端叉, 1310系列, 26 花键, 型式 CV
$48.27现货
3104-05
端叉, 花键直径 1.188", 1310系列, 轮毂直径 1.521"
$84.60现货
3104-231
端叉, 花键直径 1.26", 轮毂直径 1.562", 23 花键
$104.94现货
3104-02
端叉, 花键直径 1.146", 轮毂直径 1.844", 26 花键
$99.17现货
2-4-0523
端叉, 1310系列, 轮毂直径 2.125", 2.562" 万向节中心至端部
$43.88现货
2-4-1233
端叉 - 圆孔 1310系列, 1.500 孔键槽: 0.375, 轮毂 Diameter: 2.125
$18.91现货
5504-01 问题
5504-01 属于哪个系列?
5504-01 是 1550 系列 端叉。1550 系列标称尺寸为 1.375" 轴承盖,卡簧到卡簧宽度为 4.875". 订购前请测量旧万向节的轴承盖直径以确认系列。
5504-01 有多少个花键齿?
5504-01 在 1.609" 花键直径上有 37 个花键。 请清点输出轴上的花键并测量大径以确认。
5504-01 可替代哪些零件号?
5504-01 交叉对应于 4-4-6851-1X. 互换数据仅供参考;替代前请比对尺寸。
5504-01 有现货吗?
是的。佛罗里达仓库有 1 件现货。工作日美东标准时间(EST)下午2点前下的订单大多当天发货。