部品番号 5504-01 (別表記 5504/01) エンドヨーク, 1550シリーズ, スプライン径 1.609", ハブ径 2.500"
在庫あり1 件の出荷準備完了
在庫品の多くは 2pm(EST)までのご注文で当日発送いたします。処理時間は前後する場合があります。
- 部品注文の送料無料金額 $1,000
- 14日以内返品可能
- 適合に関するサポート: (813) 524-6491
仕様 5504-01 · 1550 Series End Yoke
- 部品番号
- 5504-01
- パーツタイプ
- エンドヨーク
- 状態
- 新品
- シリーズ
- 1550
- スタイル
- BS
- ユニバーサルジョイントから端部まで
- 4.406
- ハブ径
- 2.500"
- スプライン数
- 37
- スプライン径
- 1.609
- 通し穴
- 2.000"
- ボアタイプ
- splined
- 重量
- 5.52 lb
適合性
DANA 80
1550 シリーズのパーツには 1.375" ユニバーサルジョイントのベアリングキャップを使用します スナップリング間幅 4.875" (公称)。ご注文前に、相手側のヨークまたはジョイントのキャップ径をご確認ください。
互換品 / クロスレファレンス
- 4-4-6851-1X
5504-01 は 4-4-6851-1X と互換性があります。相互参照番号は識別用です。交換前に、上記のシリーズ、スプライン、ボルトパターンの寸法をご確認ください。
郵便番号への送料を見積もる
送料を計算
フロリダの弊社ショップからのリアルタイム UPS 送料。パーツのご注文が $1,000 送料無料 — チューブおよび完全なプロペラシャフトは常にUPSの料金で発送されます。
フロリダでの店頭受取 — 無料
5504-01 について
Replacing an end yoke is a straightforward job when you have the right part. The 5504-01 -- a UDS 1550 Series end yoke -- is dimensioned to drop onto the output shaft splines without modification, provided your shaft matches the 1.609" spline diameter and 37-spline count. This guide covers what to check before you order and what to do during installation.
Pre-Order Verification
Before removing your old yoke, record the following from either the old part or the output shaft:
- Spline diameter: Should match 1.609" for this part
- Spline count: Should match 37
- Snap ring style: BS -- check whether the groove is on the inside or outside of the bearing bore
- Series: 1550 Series -- look for the series stamp on the U-joint caps or the original yoke
Application note: DANA 80
| Specification | Value |
|---|---|
| Series | 1550 Series |
| Spline Diameter | 1.609" |
| Spline Count | 37 |
| Hub Diameter | 2.500" |
| Center U-Joint to End | 4.406" |
| Through Hole Diameter | 2.000" |
| Snap Ring Style | BS |
| Application Note | DANA 80 |
| Brand | UDS |
Dimensional Specifications
The 5504-01 carries the following dimensions, which define its fit envelope. Verify each against your application before ordering.
Installation Steps
Once you have confirmed fitment, installation proceeds as follows:
- Remove the old yoke by unthreading the retaining nut and sliding the yoke off the output shaft splines. Mark the driveshaft-to-yoke orientation before disassembly to maintain balance phasing.
- Clean the output shaft splines with a wire brush and solvent. Inspect for cracks or worn spline flanks.
- Apply a thin coat of assembly lubricant to the shaft splines. Do not over-lubricate -- excess grease can cause seal contamination.
- Slide the 5504-01 onto the splines, aligning your reference marks. The hub diameter of 2.500" should register smoothly against the seal bore.
- Install a new snap ring (BS style) in the groove. Confirm it seats fully around the perimeter.
- Torque the retaining nut to the vehicle manufacturer's specification.
After installation, lower the vehicle and drive briefly before inspecting for leaks or vibration. Any vibration at highway speed indicates a balance issue -- have the driveshaft rebalanced with the new yoke installed.
Part 5504-01 is a UDS product. Universal Driveshafts stocks a complete range of 1550 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
1550 シリーズの関連する エンドヨーク
全一覧表を見る
4-4-1901-1
エンドヨーク - スプライン穴 Series1550, Strap スタイル, 1.750x10 スプ...
$85.81在庫あり
4-4-7901-2U
エンドヨーク, 1550シリーズ - スプライン; 10x1.5 - UDS
$75.64在庫あり
3104-26CV
エンドヨーク, 1310シリーズ, 26 スプライン, スタイル CV
$48.27在庫あり
3104-05
エンドヨーク, スプライン径 1.188", 1310シリーズ, ハブ径 1.521"
$84.60在庫あり
3104-231
エンドヨーク, スプライン径 1.26", ハブ径 1.562", 23 スプライン
$104.94在庫あり
3104-02
エンドヨーク, スプライン径 1.146", ハブ径 1.844", 26 スプライン
$99.17在庫あり
2-4-0523
エンドヨーク, 1310シリーズ, ハブ径 2.125", 2.562" ジョイント・エンド間
$43.88在庫あり
2-4-1233
エンドヨーク - 丸穴 1310シリーズ, 1.500 内径キー溝: 0.375, ハブ Diamet...
$18.91在庫あり
5504-01 ご質問
5504-01 はどのシリーズですか?
5504-01 は 1550 シリーズの エンドヨーク です。 1550 シリーズの公称寸法は 1.375" ベアリングキャップです スナップリング間幅 4.875"。ご注文前に、古いジョイントのキャップ径を測ってシリーズをご確認ください。
5504-01 のスプライン数はいくつですか?
5504-01 はスプライン径 1.609" に 37 スプラインを備えています。 出力シャフトのスプライン数を数え、外径(最大径)を測って確認してください。
5504-01 はどの部品番号の代替品ですか?
5504-01 は 4-4-6851-1X とクロスリファレンス対応しています。互換データは参考情報です。交換前に寸法をご確認ください。
5504-01 の在庫はありますか?
はい。フロリダ州に 1 点の在庫がございます。平日の東部標準時(EST)午後2時までのご注文の多くは、当日中に発送いたします。