Part No. 5504-01 (also written 5504/01) End Yoke, 1550 Series, 1.609" Splines Dia, 2.500" Hub Dia
In stock1 ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 5504-01 · 1550 Series End Yoke
- Part number
- 5504-01
- Part type
- End Yoke
- Condition
- New
- Series
- 1550
- Style
- BS
- CJ to end
- 4.406
- Hub diameter
- 2.500"
- Splines count
- 37
- Splines diameter
- 1.609
- Through hole
- 2.000"
- Bore type
- splined
- Weight
- 5.52 lb
Fitment
DANA 80
1550 series parts use 1.375" u-joint bearing caps on a 4.875" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Interchange / cross-reference
- 4-4-6851-1X
5504-01 replaces or interchanges with 4-4-6851-1X. Cross-reference numbers are supplied for identification; compare the series, spline and bolt-pattern dimensions above before substituting.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 5504-01
Replacing an end yoke is a straightforward job when you have the right part. The 5504-01 -- a UDS 1550 Series end yoke -- is dimensioned to drop onto the output shaft splines without modification, provided your shaft matches the 1.609" spline diameter and 37-spline count. This guide covers what to check before you order and what to do during installation.
Pre-Order Verification
Before removing your old yoke, record the following from either the old part or the output shaft:
- Spline diameter: Should match 1.609" for this part
- Spline count: Should match 37
- Snap ring style: BS -- check whether the groove is on the inside or outside of the bearing bore
- Series: 1550 Series -- look for the series stamp on the U-joint caps or the original yoke
Application note: DANA 80
| Specification | Value |
|---|---|
| Series | 1550 Series |
| Spline Diameter | 1.609" |
| Spline Count | 37 |
| Hub Diameter | 2.500" |
| Center U-Joint to End | 4.406" |
| Through Hole Diameter | 2.000" |
| Snap Ring Style | BS |
| Application Note | DANA 80 |
| Brand | UDS |
Dimensional Specifications
The 5504-01 carries the following dimensions, which define its fit envelope. Verify each against your application before ordering.
Installation Steps
Once you have confirmed fitment, installation proceeds as follows:
- Remove the old yoke by unthreading the retaining nut and sliding the yoke off the output shaft splines. Mark the driveshaft-to-yoke orientation before disassembly to maintain balance phasing.
- Clean the output shaft splines with a wire brush and solvent. Inspect for cracks or worn spline flanks.
- Apply a thin coat of assembly lubricant to the shaft splines. Do not over-lubricate -- excess grease can cause seal contamination.
- Slide the 5504-01 onto the splines, aligning your reference marks. The hub diameter of 2.500" should register smoothly against the seal bore.
- Install a new snap ring (BS style) in the groove. Confirm it seats fully around the perimeter.
- Torque the retaining nut to the vehicle manufacturer's specification.
After installation, lower the vehicle and drive briefly before inspecting for leaks or vibration. Any vibration at highway speed indicates a balance issue -- have the driveshaft rebalanced with the new yoke installed.
Part 5504-01 is a UDS product. Universal Driveshafts stocks a complete range of 1550 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Related End Yokes in the 1550 series
See the full table
4-4-1901-1
End Yoke - Splined Bore Series1550, Strap Style, 1.750x10 Spline, 2.62...
$85.81In stock
4-4-7901-2U
End Yoke, 1550 Series - Splines; 10x1.5 - UDS
$75.64In stock
3104-26CV
End Yoke, 1310 Series, 26 Splines, Style CV
$48.27In stock
3104-05
End Yoke, 1.188" Splines Dia, 1310 Series, 1.521" Hub Dia
$84.60In stock
3104-231
End Yoke, 1.26" Splines Dia, 1.562" Hub Dia, 23 Spline
$104.94In stock
3104-02
End Yoke, 1.146" Splines Dia, 1.844" Hub Dia, 26 Spline
$99.17In stock
2-4-0523
End Yoke, 1310 Series, 2.125" Hub Dia, 2.562" Cj To End
$43.88In stock
2-4-1233
End Yoke - Round Bore 1310 Series, 1.500 Bore KEYWAY: 0.375, Hub Diame...
$18.91In stock
5504-01 questions
What series is 5504-01?
5504-01 is a 1550 series end yoke. Nominal 1550 dimensions are 1.375" bearing caps on a 4.875" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 5504-01 have?
5504-01 has 37 splines on a 1.609" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.
What part numbers does 5504-01 replace?
5504-01 cross-references to 4-4-6851-1X. Interchange data is for reference; compare the dimensions before substituting.
Is 5504-01 in stock?
Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.