Part No. 3504-60 (also written 3504/60) End Yoke, 1.276" Splines Dia, 1.875" Hub Dia
In stock1 ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3504-60 · 1350 Series End Yoke
- Part number
- 3504-60
- Part type
- End Yoke
- Condition
- New
- Series
- 1350
- Style
- UB
- Hub diameter
- 1.875
- Splines count
- 29
- Splines diameter
- 1.276
- Through hole
- 1.500"
- CJ to end
- 3.375"
- Bore type
- splined
- Weight
- 2.51 lb
Fitment
U BOLT PART NUMBER: 3-94-18, DANA 60
1350 series parts use 1.188" u-joint bearing caps on a 3.625" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 3504-60
The 1350 Series driveshaft standard has been the backbone of medium-duty automotive and light truck driveline engineering for decades. The 3504-60 end yoke from UDS is manufactured to the same dimensional standards that define this series, ensuring backward and forward compatibility across the wide range of vehicles and equipment that run 1350 Series drivetrain components.
The 1350 Series Standard Explained
Each driveshaft series -- 1100, 1310, 1350, and so on -- is defined by a specific set of U-joint cap dimensions, yoke ear geometry, and torque ratings. The 1350 Series designation tells you the cap diameter, width, and load envelope this yoke is designed for. Mixing series without proper adapter joints creates mismatched geometries that fail under load. The 3504-60 keeps everything within the 1350 Series specification.
- Spline diameter: 1.276" -- the 1350 Series output shaft standard
- Spline count: 29
- Snap ring style: UB -- standard for 1350 Series service
- Hub diameter: 1.875" -- mates with 1350 Series-rated differential or transfer case outputs
| Specification | Value |
|---|---|
| Series | 1350 Series |
| Spline Diameter | 1.276" |
| Spline Count | 29 |
| Hub Diameter | 1.875" |
| Center U-Joint to End | 3.375" |
| Through Hole Diameter | 1.500" |
| Snap Ring Style | UB |
| Application Note | DANA 60 |
| Brand | UDS |
Part Specifications
Dimensional adherence to the 1350 Series standard means this yoke will mate with any properly dimensioned 1350 Series U-joint and driveshaft. Application: DANA 60. The following table lists every critical dimension.
Ordering and Fitment Verification
Ordering the correct end yoke requires matching three numbers: the spline diameter (1.276"), the spline count (29), and the snap ring style (UB). If your shaft differs from these values, this part will not fit -- consult our fitment guide or contact our technical team before ordering.
The through hole diameter of 1.500" is relevant for applications with internal shafts or speedometer cable routing through the output yoke. The center-U-joint-to-end dimension of 3.375" must be matched to your driveshaft slip yoke or tube assembly for correct operating length.
Part 3504-60 is a UDS product. Universal Driveshafts stocks a complete range of 1350 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Related End Yokes in the 1350 series
See the full table
3504-04
End Yoke, 1.312" Splines Dia, 2.110" Hub Dia, 30 Spline
$114.87In stock
3504-09
End Yoke, 1350 Series, 1.343" Splines Dia, 1.812" Hub Dia
$121.02In stock
N3-4-JK08
End Yoke, 1350 Series, 1.250" Splines Dia, 1.85" Hub Dia
$111.55In stock
3504-03
End Yoke, 1350 Series, 1.343" Splines Dia, 1.812" Hub Dia
$102.26In stock
3504-101
End Yoke, 1350 Series, 1.375" Splines Dia, 1.750" Hub Dia
$118.59In stock
3504-85
End Yoke, 1350 Series, 1.312" Splines Dia, 1.94" Hub Dia
$108.75In stock
3504-10
End Yoke, 1350 Series, 1.188" Splines Dia, 1.875" Hub Dia"
$121.07In stock
3504-243
End Yoke, 1350 Series, 1.250" Splines Dia, 1.876" Hub Dia
$107.73In stock
3504-60 questions
What series is 3504-60?
3504-60 is a 1350 series end yoke. Nominal 1350 dimensions are 1.188" bearing caps on a 3.625" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 3504-60 have?
3504-60 has 29 splines on a 1.276" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.
Is 3504-60 in stock?
Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.