3504-02 1350 Series End Yoke

Part No. 3504-02 (also written 3504/02) End Yoke, 1.229" Splines Dia, 1.844" Hub Dia, 28 Spline

$173.81

In stock1 ready to ship

Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.

  • Free shipping on parts orders over $1,000
  • 14-day returns
  • Fitment help: (813) 524-6491

Specifications 3504-02 · 1350 Series End Yoke

How to measurePoint at a letter to read its measurement
ABCFGED
Part number
3504-02
Part type
End Yoke
Condition
New
Series
1350
Style
BS
Splines count
28
CJ to end
3.031
Hub diameter
1.844
Splines diameter
1.229
Through hole
1.375
Bore type
splined
Weight
2.64 lb

Fitment

STRAP PART NUMBER: 3-70-28, AMC 20

1350 series parts use 1.188" u-joint bearing caps on a 3.625" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.

Interchange / cross-reference

  • 3-4-11931-1X

3504-02 replaces or interchanges with 3-4-11931-1X. Cross-reference numbers are supplied for identification; compare the series, spline and bolt-pattern dimensions above before substituting.

Estimate shipping to your ZIP

Estimate shipping

Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.

Local pickup in Florida — free

About 3504-02

Finding the right end yoke starts with matching the output shaft -- and 3504-02 is engineered specifically for 1350 Series driveline applications (AMC 20). This UDS end yoke connects your transmission or transfer case output to the driveshaft with dimensional precision that eliminates slop and premature wear.

Dimensional Specifications

Before ordering any end yoke, you must verify the output shaft's spline count and diameter. The 3504-02 is built around a 1.229-inch spline diameter, 28-spline interface with BS retention. The hub measures 1.844" in diameter, and the center-of-U-joint to end distance is 3.031" -- confirming fit with your specific driveshaft length.

Specification Value
Series 1350 Series
Spline Diameter 1.229"
Spline Count 28
Hub Diameter 1.844"
Center U-Joint to End 3.031"
Through Hole Diameter 1.375"
Snap Ring Style BS
Application Note AMC 20
Brand UDS

Engineering and Material Quality

Every UDS end yoke in the 1350 Series lineup is forged or precision-machined from high-grade steel to withstand the torsional and bending loads of real-world drivetrain operation. Yoke ears are machined to consistent bearing cup bore tolerances so U-joint caps seat without rocking, preventing the micro-movement that leads to premature joint failure.

  • Consistent bearing bore dimensions for tight U-joint fit
  • Designed to OEM companion flange specifications
  • Through hole ID of 1.375" provides clearance for speedometer cables or internal shafts where applicable
  • Compatible with standard 1350 Series U-joint caps

Installation Guidance

Installation requires that the output shaft splines are clean and free of corrosion. Apply a light coat of assembly lube to the splines before pressing the yoke into position. Torque the retaining nut to OEM specification -- do not reuse stretch bolts or damaged snap rings. If the snap ring style is BS, confirm that the groove in the output shaft matches this style before installation.

Always balance the driveshaft assembly after replacing end yokes on vehicles driven above 55 mph to prevent vibration.

Part 3504-02 is a UDS product. Universal Driveshafts stocks a complete range of 1350 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.

New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.

Related End Yokes in the 1350 series

See the full table

3504-02 questions

What series is 3504-02?

3504-02 is a 1350 series end yoke. Nominal 1350 dimensions are 1.188" bearing caps on a 3.625" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.

What spline count does 3504-02 have?

3504-02 has 28 splines on a 1.229" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.

What part numbers does 3504-02 replace?

3504-02 cross-references to 3-4-11931-1X. Interchange data is for reference; compare the dimensions before substituting.

Is 3504-02 in stock?

Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.