Part No. 3503-324 (also written 3503/324) End Yoke, 1.378" Splines Dia, 1.885" Hub Dia
In stock1 ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3503-324 · 1350 Series End Yoke
- Part number
- 3503-324
- Part type
- End Yoke
- Condition
- New
- Series
- 1350
- Style
- BS
- CJ to end
- 5.594
- Hub diameter
- 1.885
- Splines count
- 31/32
- Splines diameter
- 1.378
- Through hole
- 4.094
- Bore type
- splined
- Weight
- 3.96 lb
Fitment
REPLACES 3-4-13211-1 -
1350 series parts use 1.188" u-joint bearing caps on a 3.625" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 3503-324
Every driveshaft system is only as strong as its weakest yoke. The 3503-324 is a UDS 1350 Series end yoke built to handle the torsional demands of performance applications -- from high-horsepower street builds to off-road rigs that flex the suspension to its limits. With a 1.378" spline interface and precision-machined bearing seats, this yoke transfers power cleanly without the slop that kills U-joints prematurely.
Performance-Grade Construction
The 1350 Series yoke series was developed to handle loads beyond light-duty OEM specifications. The 3503-324 carries the full load rating of the 1350 Series system, making it appropriate for high-torque applications including turbocharged and supercharged drivetrains, towing configurations, and competition use.
- Full 1350 Series torque rating -- no derating for special applications
- Precision bearing bores -- eliminate U-joint cap rocking that causes premature wear
- Snap ring style: BS -- positive retention under shock loading
- Hub diameter: 1.885" -- correct registration against diff or transfer case seal
| Specification | Value |
|---|---|
| Series | 1350 Series |
| Spline Diameter | 1.378" |
| Spline Count | 31/32 |
| Hub Diameter | 1.885" |
| Center U-Joint to End | 5.594" |
| Through Hole Diameter | 4.094" |
| Snap Ring Style | BS |
| Application Note | REPLACES 3-4-13211-1 - |
| Brand | UDS |
Specifications
Performance fitment requires exact dimensional matching. The 3503-324 is built to the following specs -- particularly relevant for REPLACES 3-4-13211-1 -:
Pairing for Maximum Drivetrain Life
The weakest link in any driveshaft assembly determines its service life. Pairing a fresh 3503-324 end yoke with a new 1350 Series U-joint and a properly balanced driveshaft eliminates the three most common failure points. For high-horsepower builds, also inspect the driveshaft tube for straightness and the slip yoke for wear -- replacing a yoke without addressing these components leaves the system vulnerable to the same vibration-induced failure.
Center-to-end measurement of 5.594" must be accounted for when calculating driveshaft operating length after suspension lifts or drivetrain swaps.
Part 3503-324 is a UDS product. Universal Driveshafts stocks a complete range of 1350 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Related End Yokes in the 1350 series
See the full table
3504-04
End Yoke, 1.312" Splines Dia, 2.110" Hub Dia, 30 Spline
$114.87In stock
3504-09
End Yoke, 1350 Series, 1.343" Splines Dia, 1.812" Hub Dia
$121.02In stock
N3-4-JK08
End Yoke, 1350 Series, 1.250" Splines Dia, 1.85" Hub Dia
$111.55In stock
3504-03
End Yoke, 1350 Series, 1.343" Splines Dia, 1.812" Hub Dia
$102.26In stock
3504-101
End Yoke, 1350 Series, 1.375" Splines Dia, 1.750" Hub Dia
$118.59In stock
3504-85
End Yoke, 1350 Series, 1.312" Splines Dia, 1.94" Hub Dia
$108.75In stock
3504-10
End Yoke, 1350 Series, 1.188" Splines Dia, 1.875" Hub Dia"
$121.07In stock
3504-243
End Yoke, 1350 Series, 1.250" Splines Dia, 1.876" Hub Dia
$107.73In stock
3503-324 questions
What series is 3503-324?
3503-324 is a 1350 series end yoke. Nominal 1350 dimensions are 1.188" bearing caps on a 3.625" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 3503-324 have?
3503-324 has 31/32 splines on a 1.378" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.
Is 3503-324 in stock?
Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.