Part No. 3326-506A (also written 3326/506A) Weld Yokes, 1330 Series, Butt Dia 4.757", Tube Dia Wall 5.000X0.125
In stock
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3326-506A · 1330 Series Weld Yoke
- Part number
- 3326-506A
- Part type
- Weld Yoke
- Condition
- New
- Brand
- UDS
- Series
- 1330
- Material
- ALUMINUM
- Butt diameter
- 4.757
- Center u-joint to weld
- 3.000"
- Tube diameter wall
- 5.000X0.125
- Weight
- 3.18 lb
Fitment
1330 series parts use 1.062" u-joint bearing caps on a 3.625" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
Fits 3326-506A
Checked against the catalog measurements: these parts fit this one.
About 3326-506A
Q: Is the 3326-506A the same as the 3326-50A except for CL-to-weld?
A: Yes -- identical in series (1330), tube spec (5.000"x0.125"), butt diameter (4.757"), and material (aluminum). The only difference is CL-to-weld: 3.000" versus 2.875". Select based on required total shaft length: the 3326-506A produces a shaft 0.125" shorter than the 3326-50A for the same tube cut.
Q: Can I mix a 3326-50A at one end and a 3326-506A at the other end of the same shaft?
A: Yes, technically -- both ends use the same 4.757" butt and 1330-series joints. The total assembled shaft length will be the sum of both CLs plus the tube length. Calculate the total carefully to ensure the correct assembled length: (2.875" + tube length + 3.000") = required shaft length. The 0.125" difference in CL will offset the tube cut required.
Q: What U-joint is required at both ends of this assembly?
A: 1330-series at 1.062" cap OD with 1330-specific cup depth. Spicer 5-3250X or equivalent. Both end yokes use the same joint series for a consistent-strength assembly. This weld yoke should be paired with matching 1330-series end yokes at the pinion for full series alignment.
Related Weld Yokes in the 1330 series
See the full table
3326-204
Weld Yokes, 1330 Series, Butt Dia 1.766", Tube Dia Wall 2.000X0.120
$22.97In stock
3326-271
Weld Yokes, 1330 Series, Butt Dia 2.625", Tube Dia Wall 2.750X0.065
$30.20In stock
3326-272
Weld Yokes, 1330 Series, Butt Dia 2.594", Tube Dia Wall 2.750X0.083
$29.42In stock
3326-306A
Weld Yokes, 1330 Series, Butt Dia 2.757", Tube Dia Wall 3.000X0.125
$48.54In stock
3326-30A
Weld Yokes, 1330 Series, Butt Dia 2.757", Tube Dia Wall 3.000X0.125
$120.02In stock
3326-356A
Weld Yokes, 1330 Series, Butt Dia 3.257", Tube Dia Wall 3.500X0.125
$48.50In stock
3326-35A
Weld Yokes, 1330 Series, Butt Dia 3.257", Tube Dia Wall 3.500X0.125
$80.25In stock
3326-40
Weld Tube Yoke 1330 Series, Fits: 4.000 x 0.083 Tube, Butt Dia: 3.844...
$37.82In stock
3326-506A questions
What series is 3326-506A?
3326-506A is a 1330 series weld yoke. Nominal 1330 dimensions are 1.062" bearing caps on a 3.625" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What tube size does 3326-506A fit?
3326-506A is machined for 5.000X0.125 driveshaft tube (outside diameter × wall thickness), with a 4.757" butt diameter. The tube must match both numbers for a correct weld fit.