Part No. 3104-10 (also written 3104/10) End Yoke, 1.125" Splines dia, 1.552" Hub Dia, 10 Splines"
In stock
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3104-10 · 1310 Series End Yoke
- Part number
- 3104-10
- Part type
- End Yoke
- Condition
- New
- Series
- 1310
- Style
- BS
- Through hole
- 1.500"
- Splines count
- 10
- CJ to end
- 3.000"
- Hub diameter
- 1.552
- Splines diameter
- 1.125
- Bore type
- splined
- Weight
- 6 lb
Fitment
DANA 44, STRAP PART NUMBER: 2-70-18
1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Interchange / cross-reference
- 2-4-2821-1X
3104-10 replaces or interchanges with 2-4-2821-1X. Cross-reference numbers are supplied for identification; compare the series, spline and bolt-pattern dimensions above before substituting.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 3104-10
Every driveshaft system is only as strong as its weakest yoke. The 3104-10 is a UDS 1310 Series end yoke built to handle the torsional demands of performance applications -- from high-horsepower street builds to off-road rigs that flex the suspension to its limits. With a 1.125" spline interface and precision-machined bearing seats, this yoke transfers power cleanly without the slop that kills U-joints prematurely.
Performance-Grade Construction
The 1310 Series yoke series was developed to handle loads beyond light-duty OEM specifications. The 3104-10 carries the full load rating of the 1310 Series system, making it appropriate for high-torque applications including turbocharged and supercharged drivetrains, towing configurations, and competition use.
- Full 1310 Series torque rating -- no derating for special applications
- Precision bearing bores -- eliminate U-joint cap rocking that causes premature wear
- Snap ring style: BS -- positive retention under shock loading
- Hub diameter: 1.552" -- correct registration against diff or transfer case seal
| Specification | Value |
|---|---|
| Series | 1310 Series |
| Spline Diameter | 1.125" |
| Spline Count | 10 |
| Hub Diameter | 1.552" |
| Center U-Joint to End | 3.000" |
| Through Hole Diameter | 1.500" |
| Snap Ring Style | BS |
| Application Note | DANA 44 |
| Brand | UDS |
Specifications
Performance fitment requires exact dimensional matching. The 3104-10 is built to the following specs -- particularly relevant for DANA 44:
Pairing for Maximum Drivetrain Life
The weakest link in any driveshaft assembly determines its service life. Pairing a fresh 3104-10 end yoke with a new 1310 Series U-joint and a properly balanced driveshaft eliminates the three most common failure points. For high-horsepower builds, also inspect the driveshaft tube for straightness and the slip yoke for wear -- replacing a yoke without addressing these components leaves the system vulnerable to the same vibration-induced failure.
Center-to-end measurement of 3.000" must be accounted for when calculating driveshaft operating length after suspension lifts or drivetrain swaps.
Part 3104-10 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Related End Yokes in the 1310 series
See the full table
3104-26CV
End Yoke, 1310 Series, 26 Splines, Style CV
$48.27In stock
3104-05
End Yoke, 1.188" Splines Dia, 1310 Series, 1.521" Hub Dia
$84.60In stock
3104-231
End Yoke, 1.26" Splines Dia, 1.562" Hub Dia, 23 Spline
$104.94In stock
3104-02
End Yoke, 1.146" Splines Dia, 1.844" Hub Dia, 26 Spline
$99.17In stock
2-4-0523
End Yoke, 1310 Series, 2.125" Hub Dia, 2.562" Cj To End
$43.88In stock
2-4-1233
End Yoke - Round Bore 1310 Series, 1.500 Bore KEYWAY: 0.375, Hub Diame...
$18.91In stock
N2-4-JK06
End Yoke, 1.25" Splines dia, 1.85" Hub Dia, 24 Spline
$115.63In stock
3104-321CV
End Yoke CV Conversion To 1310 Jeep JK NP241 07-18, counterbore by nut...
$42.66In stock
3104-10 questions
What series is 3104-10?
3104-10 is a 1310 series end yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 3104-10 have?
3104-10 has 10 splines on a 1.125" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.
What part numbers does 3104-10 replace?
3104-10 cross-references to 2-4-2821-1X. Interchange data is for reference; compare the dimensions before substituting.