Part No. 2-28-427 Weld Tube Yoke 1310 Ser', Fits: 3.000 X 0.083, CL To Weld: 1.688 Inch Butt Dia: 3.344
In stock50+ ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 2-28-427 · 1310 Series Weld Yoke
- Part number
- 2-28-427
- Part type
- Weld Yoke
- Condition
- New
- Brand
- UDS
- Series
- 1310
- Material
- STEEL
- Butt diameter
- 3.344
- Tube diameter wall
- 3.500X0.083
- Center u-joint to weld
- 1.688
- Weight
- 2.42 lb
Fitment
1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Interchange / cross-reference
- N2-28-427
- P2-28-427
2-28-427 replaces or interchanges with N2-28-427, P2-28-427. Cross-reference numbers are supplied for identification; compare the series, spline and bolt-pattern dimensions above before substituting.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
Fits 2-28-427
Checked against the catalog measurements: these parts fit this one.
Customers also bought
Parts other customers ordered together with 2-28-427.
About 2-28-427
A common engineering trade-off: using a larger-diameter tube with a lower-rated U-joint series. The 2-28-427 pairs a 3.500" OD tube -- which provides excellent torsional rigidity and high critical speed -- with a 1310-series U-joint interface that is rated lower than the 1330 or 1350. In applications where the tube is the primary structural element and peak torque is below the 1310-series limit (approximately 1,200 ft-lb), this is a valid choice. However, if peak torque is a concern, swap to the 3326-427 (1330-series) or 3556-427 (1350-series) equivalent weld yoke at the same tube size.
- Series: 1310 -- 1.062" cap diameter
- Tube: 3.500" OD x 0.083" wall steel
- Butt diameter: 3.344"
- Center U-joint to weld: 1.688"
- Critical speed of 3.5" x 0.083" x 40" shaft: approximately 6,800 RPM
Tip: for this weld yoke, confirm phasing -- both yokes on a single-piece shaft must be in phase (0 degrees) unless the shaft operates at a constant working angle where out-of-phase is specified.
Related Weld Yokes in the 1310 series
See the full table
3126-25CF
Weld Yokes, 1310 Series, Butt Dia 2.500", Tube Dia Wall 2.780X0.180
$167.80In stock
3126-261
Weld Yokes, 1310 Series, Butt Dia 2.400", Tube Dia Wall 2.550X0.080
$53.79In stock
3126-306A
Weld Yokes, 1310 Series, Butt Dia 2.757", Tube Dia Wall 3.00X0.125
$58.47In stock
3126-30A
Weld Yokes, 1310 Series, Butt Dia 2.757", Tube Dia Wall 3.00X0.125
$79.10In stock
3126-30CF
Weld Yokes, 1310 Series, Butt Dia 3.000", Tube Dia Wall 3.260X0.130
$120.48In stock
3126-31A
Weld Yokes, 1310 Series, Butt Dia 2.844", Tube Dia Wall 3.00X0.083
$77.98In stock
3126-356A
Weld Yokes, 1310 Series, Butt Dia 3.257", Tube Dia Wall 3.500X0.125
$71.48In stock
3126-35A
Weld Yokes, 1310 Series, Butt Dia 3.257", Tube Dia Wall 3.500X0.125
$86.53In stock
2-28-427 questions
What series is 2-28-427?
2-28-427 is a 1310 series weld yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What tube size does 2-28-427 fit?
2-28-427 is machined for 3.500X0.083 driveshaft tube (outside diameter × wall thickness), with a 3.344" butt diameter. The tube must match both numbers for a correct weld fit.
What part numbers does 2-28-427 replace?
2-28-427 cross-references to N2-28-427, P2-28-427. Interchange data is for reference; compare the dimensions before substituting.
Is 2-28-427 in stock?
Yes. 50+ are in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.