Part No. 3104-266 (also written 3104/266) End Yoke, 1.146" Splines Dia, 1.500" Hub Dia, 26 Spline
In stock2 ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3104-266 · 1310 Series End Yoke
- Part number
- 3104-266
- Part type
- End Yoke
- Condition
- New
- Series
- 1310
- Style
- SR
- Hub diameter
- 1.500"
- Splines count
- 26
- Splines diameter
- 1.146
- CJ to end
- 2.875
- Through hole
- 1.469
- Bore type
- splined
- Weight
- 6 lb
Fitment
OSR TYPE - USED ON NISSAN - FORD - TOYOTA SHAFTS AND MORE
1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 3104-266
3104-266 is a UDS 1310 Series end yoke. Spline diameter: 1.146". Spline count: 26. Hub diameter: 1.500". Retention style: SR. This is the replacement specification for 1310 Series output shafts in OSR TYPE - USED ON NISSAN - FORD - TOYOTA SHAFTS AND MORE applications. If your numbers match, this is your part.
Engineering Specifications
All dimensions are as-machined. Match each to your output shaft before ordering. No modification required for correct-fit installations.
| Specification | Value |
|---|---|
| Series | 1310 Series |
| Spline Diameter | 1.146" |
| Spline Count | 26 |
| Hub Diameter | 1.500" |
| Center U-Joint to End | 2.875" |
| Through Hole Diameter | 1.469" |
| Snap Ring Style | SR |
| Application Note | OSR TYPE - USED ON NISSAN - FORD - TOYOTA SHAFTS AND MORE |
| Brand | UDS |
Snap Ring and Retention Detail
The SR retention system on this yoke uses a standard snap ring seated in the output shaft groove. The groove geometry dictates which snap ring style is required -- do not substitute ISR hardware in an OSR groove or vice versa. Snap ring ejection under load is a catastrophic failure mode that can damage adjacent driveline components.
Through bore ID: 1.469" -- required clearance dimension for applications with internal shafts.
Ordering and Cross-Reference
Part number 3104-266 corresponds to UDS part number 3104-266. Application: OSR TYPE - USED ON NISSAN - FORD - TOYOTA SHAFTS AND MORE Cross-reference against your existing yoke OEM part number to confirm compatibility before placing an order.
This yoke is stocked at Universal Driveshafts and ships the same business day when ordered before the daily cutoff. Combine with a 1310 Series U-joint for a complete output shaft service kit.
Part 3104-266 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Related End Yokes in the 1310 series
See the full table
3104-26CV
End Yoke, 1310 Series, 26 Splines, Style CV
$48.27In stock
3104-05
End Yoke, 1.188" Splines Dia, 1310 Series, 1.521" Hub Dia
$84.60In stock
3104-231
End Yoke, 1.26" Splines Dia, 1.562" Hub Dia, 23 Spline
$104.94In stock
3104-02
End Yoke, 1.146" Splines Dia, 1.844" Hub Dia, 26 Spline
$99.17In stock
2-4-0523
End Yoke, 1310 Series, 2.125" Hub Dia, 2.562" Cj To End
$43.88In stock
2-4-1233
End Yoke - Round Bore 1310 Series, 1.500 Bore KEYWAY: 0.375, Hub Diame...
$18.91In stock
N2-4-JK06
End Yoke, 1.25" Splines dia, 1.85" Hub Dia, 24 Spline
$115.63In stock
3104-321CV
End Yoke CV Conversion To 1310 Jeep JK NP241 07-18, counterbore by nut...
$42.66In stock
3104-266 questions
What series is 3104-266?
3104-266 is a 1310 series end yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 3104-266 have?
3104-266 has 26 splines on a 1.146" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.
Is 3104-266 in stock?
Yes. 2 are in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.