Part No. 3104-262CV End Yoke, 1310 Series, 1.146" Splines Dia, 1.614" Hub Dia
In stock1 ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3104-262CV · 1310 Series End Yoke
- Part number
- 3104-262CV
- Part type
- End Yoke
- Condition
- New
- Series
- 1310
- Style
- CV
- Through hole
- 1.500"
- CJ to end
- 3.000"
- Splines count
- 26
- Splines diameter
- 1.146
- Hub diameter
- 1.614
- Bore type
- splined
- Weight
- 2.2 lb
Fitment
CV CONVERSION YOKE, INCLUDES HUB SLEEVE, DODGE & JEEP FRONT TRANSFER CASE
1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Interchange / cross-reference
- 3104-262CV-01
3104-262CV replaces or interchanges with 3104-262CV-01. Cross-reference numbers are supplied for identification; compare the series, spline and bolt-pattern dimensions above before substituting.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
About 3104-262CV
Finding the right end yoke starts with matching the output shaft -- and 3104-262CV is engineered specifically for 1310 Series driveline applications (CV CONVERSION YOKE, INCLUDES HUB SLEEVE). This UDS end yoke connects your transmission or transfer case output to the driveshaft with dimensional precision that eliminates slop and premature wear.
Dimensional Specifications
Before ordering any end yoke, you must verify the output shaft's spline count and diameter. The 3104-262CV is built around a 1.146-inch spline diameter, 26-spline interface with CV-style retention. The hub measures 1.614" in diameter, and the center-of-U-joint to end distance is 3.000" -- confirming fit with your specific driveshaft length.
| Specification | Value |
|---|---|
| Series | 1310 Series |
| Spline Diameter | 1.146" |
| Spline Count | 26 |
| Hub Diameter | 1.614" |
| Center U-Joint to End | 3.000" |
| Through Hole Diameter | 1.500" |
| Snap Ring Style | CV |
| Application Note | CV CONVERSION YOKE, INCLUDES HUB SLEEVE |
| Brand | UDS |
Engineering and Material Quality
Every UDS end yoke in the 1310 Series lineup is forged or precision-machined from high-grade steel to withstand the torsional and bending loads of real-world drivetrain operation. Yoke ears are machined to consistent bearing cup bore tolerances so U-joint caps seat without rocking, preventing the micro-movement that leads to premature joint failure.
- Consistent bearing bore dimensions for tight U-joint fit
- Designed to OEM companion flange specifications
- Through hole ID of 1.500" provides clearance for speedometer cables or internal shafts where applicable
- Compatible with standard 1310 Series U-joint caps
Installation Guidance
Installation requires that the output shaft splines are clean and free of corrosion. Apply a light coat of assembly lube to the splines before pressing the yoke into position. Torque the retaining nut to OEM specification -- do not reuse stretch bolts or damaged snap rings. If the snap ring style is CV, confirm that the groove in the output shaft matches this style before installation.
Always balance the driveshaft assembly after replacing end yokes on vehicles driven above 55 mph to prevent vibration.
Part 3104-262CV is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.
New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.
Related End Yokes in the 1310 series
See the full table
3104-26CV
End Yoke, 1310 Series, 26 Splines, Style CV
$48.27In stock
3104-05
End Yoke, 1.188" Splines Dia, 1310 Series, 1.521" Hub Dia
$84.60In stock
3104-231
End Yoke, 1.26" Splines Dia, 1.562" Hub Dia, 23 Spline
$104.94In stock
3104-02
End Yoke, 1.146" Splines Dia, 1.844" Hub Dia, 26 Spline
$99.17In stock
2-4-0523
End Yoke, 1310 Series, 2.125" Hub Dia, 2.562" Cj To End
$43.88In stock
2-4-1233
End Yoke - Round Bore 1310 Series, 1.500 Bore KEYWAY: 0.375, Hub Diame...
$18.91In stock
N2-4-JK06
End Yoke, 1.25" Splines dia, 1.85" Hub Dia, 24 Spline
$115.63In stock
3104-321CV
End Yoke CV Conversion To 1310 Jeep JK NP241 07-18, counterbore by nut...
$42.66In stock
3104-262CV questions
What series is 3104-262CV?
3104-262CV is a 1310 series end yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What spline count does 3104-262CV have?
3104-262CV has 26 splines on a 1.146" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.
What part numbers does 3104-262CV replace?
3104-262CV cross-references to 3104-262CV-01. Interchange data is for reference; compare the dimensions before substituting.
Is 3104-262CV in stock?
Yes. 1 is in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.