3104-25 1310 Series End Yoke

Part No. 3104-25 (also written 3104/25) End Yoke, 1.085" Splines Dia, 25 Spline

$94.39

In stock

Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.

  • Free shipping on parts orders over $1,000
  • 14-day returns
  • Fitment help: (813) 524-6491

Specifications 3104-25 · 1310 Series End Yoke

How to measurePoint at a letter to read its measurement
ABCFGED
Part number
3104-25
Part type
End Yoke
Condition
New
Series
1310
Style
UB
Through hole
1.500"
Splines count
25
CJ to end
2.875
Hub diameter
1.521
Splines diameter
1.085
Bore type
splined
Weight
2.16 lb

Fitment

U BOLT PART NUMBER: 2-94-28, GM 8.2

1310 series parts use 1.062" u-joint bearing caps on a 3.219" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.

Estimate shipping to your ZIP

Estimate shipping

Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.

Local pickup in Florida — free

About 3104-25

A worn or damaged end yoke is one of the most common causes of driveline vibration and U-joint failure -- yet it's often overlooked during diagnosis. The 3104-25 from UDS provides a direct, properly dimensioned replacement for 1310 Series applications, specifically engineered for GM 8.2, restoring the tight tolerances that eliminate vibration at the source.

The Problem: Worn Yoke Geometry

When end yoke bores wear oval or the snap ring groove erodes, U-joint caps begin to rock in their seats. This produces a clicking or clunking noise at low speed, a vibration that tracks with vehicle speed, and -- in severe cases -- catastrophic U-joint ejection. The 3104-25 replaces the worn geometry with new machined surfaces: 1.085" spline bore, 1.521" hub diameter, bearing bores held to 1310 Series tolerances.

Specification Value
Series 1310 Series
Spline Diameter 1.085"
Spline Count 25
Hub Diameter 1.521"
Center U-Joint to End 2.875"
Through Hole Diameter 1.500"
Snap Ring Style UB
Application Note GM 8.2
Brand UDS

Specifications That Guarantee Fit

Precision fit starts with matching three numbers: spline count, spline diameter, and snap ring style. The 3104-25 is built to the following dimensions -- verify each against your output shaft before ordering.

Long-Term Reliability

The UDS manufacturing process subjects each yoke to dimensional inspection before shipment. Bearing bore roundness, spline form, and hub diameter are checked against 1310 Series master gauges. The result is a yoke that installs without hammering, retains U-joint caps securely under high-cycle loading, and seals against output shaft oil seals without leaking.

  • Through hole: 1.500" -- clears internal shafts and cables
  • Center U-joint to end: 2.875" -- maintains correct driveshaft length
  • Snap ring style: UB -- matches OEM retention method
  • Drop-in replacement -- no machining required

Part 3104-25 is a UDS product. Universal Driveshafts stocks a complete range of 1310 Series end yokes, U-joints, and driveshaft components. Contact our technical team for fitment assistance.

New to end yokes? Our end yoke guide explains splines, snap-ring styles, and how to measure.

Related End Yokes in the 1310 series

See the full table

3104-25 questions

What series is 3104-25?

3104-25 is a 1310 series end yoke. Nominal 1310 dimensions are 1.062" bearing caps on a 3.219" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.

What spline count does 3104-25 have?

3104-25 has 25 splines on a 1.085" spline diameter. Count the splines on the output shaft and measure across the major diameter to confirm.