Part No. 3-28-57-1 Weld Tube Yoke 1350 Ser', Fits: 2.750 x 0.083, Butt Dia: 2.594 Inch CL To Weld: 2 Inch SOLID BUTT
In stock33 ready to ship
Most stock parts ship the same day when ordered before 2pm EST; processing times may vary.
- Free shipping on parts orders over $1,000
- 14-day returns
- Fitment help: (813) 524-6491
Specifications 3-28-57-1 · 1350 Series Weld Yoke
- Part number
- 3-28-57-1
- Part type
- Weld Yoke
- Condition
- New
- Brand
- UDS
- Series
- 1350
- Material
- STEEL
- Center u-joint to weld
- 2.000"
- Butt diameter
- 2.594
- Tube diameter wall
- 2.750X0.083
- Weight
- 3 lb
Fitment
SOLID BUTT - CAN BE TURN DOWN TO 2.000 X 0.125
1350 series parts use 1.188" u-joint bearing caps on a 3.625" snap-ring-to-snap-ring width (nominal). Confirm the cap diameter on the mating yoke or joint before ordering.
Estimate shipping to your ZIP
Estimate shipping
Live UPS rates from our shop in Florida. Parts orders over $1,000 ship free — tubing and complete driveshafts always ship at the UPS rate.
Local pickup in Florida — free
Fits 3-28-57-1
Checked against the catalog measurements: these parts fit this one.
Customers also bought
Parts other customers ordered together with 3-28-57-1.
About 3-28-57-1
3-28-57-1: 1350 Series Weld Tube Yoke -- Drivetrain Component Guide
The drivetrain has no redundant load paths -- every torque-carrying component must perform correctly or the system fails. The 3-28-57-1 is the weld tube yoke position in that load chain for 1350 series applications, providing tube OD 2.750 x wall 0.083, butt dia 2.594 with forged construction and production-controlled tolerances.
Specification Data
| Specification | Value |
|---|---|
| Series | 1350 |
| Tube OD x Wall | 2.750X0.083 |
| Butt Dia | 2.594 |
| CJ to Weld | 2.000" |
| Material | STEEL |
| Brand | UDS |
| Part Number | 3-28-57-1 |
Failure Modes and Prevention
A worn weld tube yoke typically presents as vibration at certain speed ranges, a clunk on throttle engagement, or visible play when you grab the driveshaft near the yoke and rock it. Left unaddressed, it accelerates u-joint wear, can score the output shaft seal contact area, and in severe cases causes shaft separation. Replacing the 3-28-57-1 as part of a scheduled drivetrain refresh -- rather than waiting for failure -- is the lower-cost strategy in the long run.
Fitment Checklist
- Tube od 2.750 x wall 0.083, butt dia 2.594 -- verified against this part before ordering
- Series 1350 u-joint cross in service or on order for this shaft end
- Mating component (output shaft / companion flange) in serviceable condition
- Retaining hardware (snap rings, strap bolts, or flange bolts as applicable) renewed if previously heat-cycled
- Shaft balance acceptable after installation -- road test confirms this
Note: SOLID BUTT - CAN BE TURN DOWN TO 2.000 X 0.125
Order the 3-28-57-1 from Universal Driveshafts today. In-stock items ship fast from our warehouse.
Related Weld Yokes in the 1350 series
See the full table
3526-201
Weld Yokes, 1350 Series, Butt Dia 1.766", Tube Dia Wall 2.000X0.120
$35.20In stock
3-28-777
Weld Tube Yoke 1350 Ser', Fits 2.000 X 0.120 Tube, Butt Dia: 1.766
$18.07In stock
3526-306A
Weld Yokes, 1350 Series, Butt Dia 2.757", Tube Dia Wall 3.000X0.125
$48.54In stock
3526-30A
Weld Yokes, 1350 Series, Butt Dia 2.757", Tube Dia Wall 3.000X0.125
$86.48In stock
3526-30CF
Weld Yokes, 1350 Series, Butt Dia 3.000", Tube Dia Wall 3.260X0.130
$169.90In stock
3526-356A
Weld Yokes, 1350 Series, Butt Dia 3.257", Tube Dia Wall 3.500X0.125
$48.54In stock
3526-35A
Weld Yokes, 1350 Series, Butt Dia 3.257", Tube Dia Wall 3.500X0.125
$73.05In stock
3526-35CF
Weld Yokes, 1350 Series, Butt Dia 3.500", Tube Dia Wall 3.790X0.145
$184.34In stock
3-28-57-1 questions
What series is 3-28-57-1?
3-28-57-1 is a 1350 series weld yoke. Nominal 1350 dimensions are 1.188" bearing caps on a 3.625" snap-ring-to-snap-ring width. Measure the cap diameter on your old joint to confirm the series before ordering.
What tube size does 3-28-57-1 fit?
3-28-57-1 is machined for 2.750X0.083 driveshaft tube (outside diameter × wall thickness), with a 2.594" butt diameter. The tube must match both numbers for a correct weld fit.
Is 3-28-57-1 in stock?
Yes. 33 are in stock in Florida. Most stock orders placed before 2 pm EST on a weekday ship the same day.