N.º de parte 027SG80004 Cabezales de doble junta CV, Diám. círculo de pernos 3.386", Diám. agujero de perno 330", Diám. piloto 3.937
En stock
La mayoría de las piezas en stock salen el mismo día si se piden antes de las 2pm EST; los tiempos de procesamiento pueden variar.
- Envío gratis en pedidos de piezas de más de $1,000
- Devoluciones en 14 días
- Ayuda con la compatibilidad: (813) 524-6491
Especificaciones 027SG80004 · CV Double Joint Head
- Número de pieza
- 027SG80004
- Tipo de pieza
- CV Double Joint Head
- Condición
- Nuevo
- Diám. círculo de pernos
- 3.386
- Diámetro de centrado
- 3.937
- Diám. agujero de perno
- 330
- Estilo / serie
- CVJ
- Diámetro de asiento
- 2.375
- Extremo a soldadura
- 6.125 COMPRESSED
- Diám. y pared de tubo
- 2.500X0.065
- Peso
- 5 lb
Compatibilidad
Fits 01-05 Ford Escape/Mazda Tribute rear shaft at transaxle
Calcula el envío a tu código postal
Calcular envío
Tarifas UPS en vivo desde nuestro taller en Florida. Los pedidos de piezas de más de $1,000 tienen envío gratis; el tubo y los cardanes completos siempre se envían con la tarifa UPS.
Retiro en tienda en Florida: gratis
Piezas alternativas para 027SG80004
Misma compatibilidad, otro número o marca. Revisa las notas antes de sustituir.
| Agregar | Foto | N.º de parte | Precio | Style series | Diám. y pared de tubo | Diámetro de asiento | Diám. agujero de perno | Extremo a soldadura | Diám. círculo de pernos | Notas |
|---|---|---|---|---|---|---|---|---|---|---|
![]() |
2690-100 |
$334.10
|
CVJ | 2.500X0.065 | 2.375 | 330 | 6.125 COMPRESSED | 3.386 | Fits 01-05 Ford Escape/Mazda Tribute rear shaft at transaxle |
Acerca de 027SG80004
When a driveshaft must operate at angles exceeding 3-5 degrees continuously, a conventional Cardan joint introduces measurable speed variation at twice the shaft rotation frequency. The 027SG80004 solves this with a double-joint constant-velocity head in the CVJ series -- the industry's proven approach to high-angle driveshaft applications in off-road, military, and commercial vehicle platforms.
Dimensional Specifications
| Parameter | Value |
|---|---|
| Series | CVJ |
| Bolt Circle Diameter | 3.386" |
| Butt Diameter | 2.375" |
| End to Weld | 6.125 COMPRESSED" |
| Tube Diameter x Wall | 2.500X0.065" |
| Pilot Diameter | 3.937" |
| Notes / Application | Fits 01-05 Ford Escape/Mazda Tribute rear shaft at transaxle |
| Part Number | 027SG80004 |
How CV Double Joints Eliminate Vibration
A double-Cardan joint achieves constant-velocity motion by arranging two single U-joints in series, phased so that each joint's velocity variation is equal and opposite to the other's. A centering ball-and-socket assembly maintains the midpoint angle precisely at half the total operating angle. The result: velocity error at the first joint is exactly cancelled by the second joint, and the output shaft rotates at a perfectly constant speed regardless of the total operating angle -- up to the joint's rated maximum.
The 027SG80004 is rated for continuous operation at angles typical of lifted trucks and transfer case applications, and is grease-serviceable through standard U-joint Zerk fittings to extend service intervals in demanding environments.
Tube Welding and Assembly Considerations
The butt-weld end of the 027SG80004 is machined for 2.500X0.065 driveshaft tube. Proper weld preparation -- clean, square-cut tube ends, correct gap, and a preheat in cold conditions -- is as important as the joint selection itself. A poorly welded joint head introduces runout that no amount of dynamic balancing can fully correct. After welding, the completed shaft should be balanced to within 0.1 oz-in per foot of shaft length for best NVH results.
- Verify the bolt circle diameter and hole count match the companion flange before final assembly
- Grease the centering socket and both bearing crosses at initial assembly and every 30,000 miles thereafter
- Check for centering socket wear if vibration returns after lubrication -- a worn socket allows the midpoint angle to drift, degrading velocity cancellation
- Maintain proper driveshaft phasing (yoke ears in-phase) when assembling the complete shaft
Order from a Driveline Specialist
Universal Driveshafts stocks the 027SG80004 and the full range of CVJ CV joint components for same-day shipment. Our driveline engineers can assist with angle measurement, tube selection, and complete shaft specifications for custom build projects. Contact us with your vehicle's operating angle and torque requirement for a personalized recommendation.
CV Double Joint Heads relacionados
Ver la tabla completa
027SG80002
Cabezales de doble junta CV, Diám. piloto 3.819", Diám. círculo de per...
$363.88En stock
032SG80002
Cabezales de doble junta CV, CVJ serie, Diám. círculo de pernos 3.583"...
$351.72En stock
2552-8780
Cabezales de doble junta CV, CVJ serie, Diám. de asiento 2.344", Diám....
$119.98En stock
2690-100
Cabezales de doble junta CV, CVJ serie, Diám. círculo de pernos 3.386"...
$334.10En stock
2752-8734
Cabezales de doble junta CV, CVJ serie, Diám. de asiento 2.344", Diám....
$66.94En stock
3190-100
Cabezales de doble junta CV, CVJ serie, Diám. círculo de pernos 3.386"...
$181.15En stock
3190-107
Cabezales de doble junta CV, CVJ serie, Diám. de asiento 1.571", Diám....
$351.83En stock
9994-01
Cabezales de doble junta CV, CVJ serie, Diám. círculo de pernos 3.925"...
$240.64En stock